Search results

a simple lowpass filter after the freeverb removed the noise.

Hi Paul, I tried to new free verb effect. It works very nicely. Only when i use oscillators as input for the freeverb, I can hear a really light noise in the background. Any idea how i can remove this?

Ye to bad i disconnected the wiring, so i cant make a picture. Like thermingeineur said, maybe it is the amplified speakers. I did change to some other speakers with different amplifier. I connect the minijack to this board: https://www.adafruit.com/product/1752. This audio amplifier board was...

I quickly detached everything out of panic, so dont have picture now. The following was connected: RFM unit using: * SPI2 pins * Ground and 3.3v on teensy A tft touch screen. * SPI1 pins (alternative because of audioboard) * ground on teensy * 3.3v for reset screen on teensy * vin on teensy...

Hi there, I am using a audioboard with teensy 3.6 for a while. Today suddenly the audioboard started to smoke. The chip in the middle got burned. When i put the usb in the teensy. The center part of the audioboard starts to heat up. I removed all the other cables from the teensy and still...

Thats a good blind guess! I changed the SPI clock to 24mhz and now it always works on when i build on cpu 180mhz. Thanks.

yes i tried different delays. thanks for your suggestions. i dont have a logic analyser nor oscilloscope to dive deeper in this.

With delay between begin and fill there is a bigger change it continues, but still gets stuck most of the times.

For anyone who wants to use the 3.5 inch touch shield of adafruit. It took me quite some time to find the right setup, because the HX8357 libraries dont work well on teensy. Here example of my configuration (build on max 168mhz): /*************************************************** This is...

I just used the basic examples that come with the libraries. I tried the delay, but that didnt work. You mean just a normal delay after setup right? Slowering down cpu only works.

I figured out that the ILI9341_t3 only works correct, if i set the cpu speed to 168 mhz or lower. Now it doesnt crash on start.

Hello, Im trying to make this screen: https://learn.adafruit.com/adafruit-3-5-color-320x480-tft-touchscreen-breakout/pinouts to work with Teensy 3.6 and ILI9341_t3 library. I discovered that this https://github.com/PaulStoffregen/Adafruit_HX8357_Library doesnt really work with my screen. The...

Hi Paul, Im also strugling with the HX8357D library. Like the others in here, I was able to use the ILI9341 library with the 3.5 inch HX8357D screen. It doesnt work perfect though, it only works sometimes. Did anyone got the HX8357D library to work?

thanks! will give that a try

Hi everybody, Does anyone know how to disable the screen going to white on startup? I use ILI9341_t3 library which works fine with my screen. Only when I plug in the power and the library loads, the screen starts with white pixels. This creates a annoying white flash at startup. Not a huge...

Hi there, Can anyone tell me if it is possible to change the waveform of the Sine Fm component? Greetings, B van Geer

Thanks a lot. It worked and everything is under control. I cant believe you give support to everyone like this! Teensy rocks.

thanks will try!

i used these pinouts: MOSI 11 MISO 12 SCK 13 CS 17 DIO 0 14 RST 24 which work well, the radio works

Yes i think i miss understood indeed. I connected a rfm69 unit to spi0 and than the audioboard stopped working. So thats why i thought audioboard interfered with the rfm69 chip. Thanks for the help. Maybe the rfm uses some other pins that are used by audioboard. I will take a better look.

Thank you Paul. Is it possible to use audioboard on spi1 so i can use other device on spi0 ? where do i have to change this in the audio library code?

Hi, Can you help me change the spi pins for the audio board in the library? Would SPI.setMOSI(pin), SPI.setMISO(pin), and SPI.setSCK(pin) be enough? I tried to change them to mosi1-0,miso1-1 and sck1-32 on teensy 3.6 , but it doesnt work yet. Where can i change the pins in the library?

Thanks this works for me ! Although I had to set it to 2 mhz. I think thats the standard setting on teensy?

Thanks a lot ! this helped me out

Im sorry. I made a mistake in my original code. Ill close the topic. Thanks for feedback!

Hi there, I started to have some troubles with one of my projects. Suddenly my floats in a array start to do funky. The first number in the float array is fine. But all the other floats are being misplaced two decimals. See the screen capture of the monitor + script. Please help!