Search results

I recently encountered the inability to flash as well (on a new Teensy 4.0 but guessing that's not the issue) after an abrupt Windows update & brownout. Paul: thanks for reminding me of this simple tip! :)

Quick note to say an extreme thanks to @houston == Paul (and MarkT & boxofrobots). I was able to get it to work and now integrating it into the final Halloween prop (a creepy doll). If I have time before the reveal to my husband...I may try to get the crossfading in. I have done some forum...

fyi: My background is in computer graphics and I thought I could make the leap into Teensy but my health issues...(previous brain infection + surgery requiring daily iv abx for 3+ months) make connections more difficult than the average bear/joe. But once things "click"...I'm like Rain Man! I...

I'm absolutely aware of the falsehood of the term "realtime reverse audio" and I should not have put that in the subject line (oopsie!). So, essentially a delay...queue...reversal of the queue...then output...with some sort effect (envelope/fade?) of joining between packets (sorry I'm probably...

I have SO much to learn. I'm googling 'envelope' audio effect in a moment as I have no musical background. I hope it will be actual reversal of the audio but if not, at least I will be learning more. :) I can't lose this contest against my husband! haha! And thank you again.

So I will study effect_envelope.cpp & .h files. I seem to hit a brick wall not knowing how to properly modify within the ino sketch (or anywhere lol). But that is due to my lack of programming skills. Thank you so much for steering me in the right direction, @boxxofrobots! I will try again...

I'm not as smart as most in this forum so I apologize for asking if this is a simple project. I plan on going through the audio tutorial (again) tomorrow...in hopes for things to 'sink in'. My husband has challenged me to do a Halloween project. I have every Teensy board available, along...

I've also been having some of issues (not seeing teensy port, sd card failure, etc) since updating to the latest Teensyduino and 1.8.9 Arduino IDE. I also had an unwanted Windows update (grr). What I've done for the missing port is go into Device Manager, View Hidden, then delete all the ports...

Thank you, rcarr & Flophi for the replies. This morning I did a better google search and learned some more. My error was not putting a while(state == X)! When I post in the future, I will think about the items that rcarr suggested, then sleep on it...because many times I'm able to figure it out...

I'm attempting to learn about state machines (fsm) and encountering some difficulties. I'm not the brightest bulb in the pack so I know someone here can direct me! Here is what I want to do: Using the Emic2 speech board alongside a teensy 3.6 and/or 3.2 (audio shield optional and I also have...

I think it's confusing the way the pins are labeled on this display. I've been trying to connect this display with Teensy 3.6 but haven't had any luck. I'm sure I am mixing up the pin names (I'm a noob). I've been up since 3am so will try again tomorrow. A good night's sleep can make a huge...

I was able to get emic working with both 3.2 & 3.6. Apparently my audio cable was bad! So, in the future I will check the most simple things first! lol I will continue to try to get TeensyTransfer to work later on. Thanks again to defragster & tonton81 for your helpful advice. Merry Christmas!

Thanks, defragster. As a newbie, it makes sense for me to follow the same hardware setup that the examples use. But...if I wanted to modify the Talkie library to work with my audio tutorial kit...which uses the audio shield for output, could I easily do that? Or is it only for prop shield? And...

Thank you! I have seen this link before but I think my membership to the pjrc forum was not good earlier...because now I can actually download attachments. Hopefully, it will make sense to me as that link is for a very complex (and amazing) project! The wiring to the emic2 seems to be tripping...

Hello, This is more of a general post so I won't be attaching any code. I really like Teensy but I'm having a terrible time getting started because I am new to electronics and microcontrollers. I've tinkered with Arduino Uno and Mega 2560 but that's it. I decided to check out Teensy (first I...