Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • loglow's Avatar
    10-19-2019, 05:37 AM
    Hi everyone, I haven't been nearly as responsive here as I'd like to be, since I've had a lot going on over the last several weeks, some of which was unexpected. I'll be on a train with Wi-Fi (hopefully) for at...
    263 replies | 14769 view(s)
  • loglow's Avatar
    10-02-2019, 05:34 PM
    Hi all, Iím sorry for my silence this past week, Iíve been extraordinarily busy. Iíll try to catch up with everyone on here tonight.
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-23-2019, 04:29 AM
    Hey all! You guys are awesome. Got home safely, but then had a crazy busy weekend. Looks like I have some work to do! I should be able to make revisions this week. I might hold off on sending out more kits...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-15-2019, 05:20 AM
    Wow, thanks everyone for all the detailed tests and replies here! Just wanted to pop in and say that I'm away from home until late on Wednesday (9/18) so I won't be able to ship anything else out until then. I might...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-12-2019, 06:11 AM
    How do folks feel about this kind of battery holder? Only works with 1220 (and maybe 1225) cells, but that's the most common thickness anyway. Examples: MPD BC501SM Keystone 1056
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-12-2019, 05:38 AM
    My technique with these has been: apply flux, place component, tape it down if necessary (I usually don't), heat up it tip of one pad without touching the header, then apply some solder to the pad only (without touching...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-12-2019, 05:01 AM
    I agree. The most difficult thing for me is the SD socket because of its little overhang. I'm excited to investigate the possibility of the "removable" cover, because that alone could remedy this. Also, the order of...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-12-2019, 04:43 AM
    I have Socket Kits put together now. Happy to send you one! That goes for anyone else beta testing too. Let me know if you'd like a Socket Kit and/or another Breakout kit along with it. This is very sound advice....
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-06-2019, 05:10 AM
    I don't think the (stated) 0.43 mm difference would matter in practice, and I suspect that the same pogo pins would still work too. Keep in mind that to fully socket the Teensy (3.6 or 4.0) you'd have to order a...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-05-2019, 05:27 AM
    I order these headers directly from Samtec. Their online ordering is fine overall, but very annoying when it comes to shipping costs since it doesn't calculate them for you, so you just have to guess. I've had some...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-05-2019, 05:12 AM
    The back of the pinout card will have the dimensional drawing on it. The mux table will be printed on legal size paper (8.5 x 14) so will be easy to read.
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-02-2019, 08:09 AM
    Here's a revised pinout card: Added CS1 to pin 0 Added MISO1 to pin 1 Reduced the size of the gray digital pin number bubbles Rearranged the blue & green bubbles on the left side Swapped locations of CRX1/CTX1...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-02-2019, 07:27 AM
    Ok, this is a bit of a tangent, but... I made a pin mux table based on section 9.1.1 (pages 289-316) of the i.MX RT1060 Processor Reference Manual. i.MX RT1060 Pin Mux Table CSV (zipped): Teensy 4.0 Pins Mux...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-01-2019, 10:21 PM
    Dis you mean will the back of the card have anything on it? I wasn't planning on it. Anything useful you'd like to see there?
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-01-2019, 10:07 PM
    I don't know yet. I still have to get my hands on one of those pressure fit connectors to test it with the flex cable. The datasheet indicates a recommended thickness of 3.0 Ī 0.05 mm and the flex cable is 2.6 mm thick....
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-01-2019, 09:50 PM
    So, I cross-referenced my pinout card with the data from @KurtE, and this is the result: Light red background = Not currently included on pinout card Red text = Alternate pin for this function Green background...
    263 replies | 14769 view(s)
  • loglow's Avatar
    09-01-2019, 07:23 AM
    Thanks for the feedback everyone! I don't think I'm going to send out any of the first run (mistake) boards, just because I don't want to cause any unnecessary confusion (for myself or anyone else). I'm still...
    263 replies | 14769 view(s)
  • loglow's Avatar
    08-30-2019, 10:46 PM
    The basic kit will include totally generic tin-plated square-post header strips. The ones pictured here, which will be included in the optional Socket Kit, are Samtec low-profile socket strips (SLW-1**-01-F-S and -D)...
    263 replies | 14769 view(s)
  • loglow's Avatar
    08-30-2019, 10:16 PM
    The assembled (socketed) breakout without Teensy: The assembly showing flex cable and socket (the locking tab is flipped up in the left photo): The Teensy by itself with headers and flex cable attached: ...
    263 replies | 14769 view(s)
  • loglow's Avatar
    08-30-2019, 10:01 PM
    Here's an update! I got the first batch of test boards back. The flex cables look good, and seem to work fine, both in terms of direct soldering, or when used with a connector socket. They are 0.26 mm thick, which...
    263 replies | 14769 view(s)
  • loglow's Avatar
    08-26-2019, 07:11 PM
    PM sent. Yes, there certainly will be a pre-assembled option!
    263 replies | 14769 view(s)
No More Results
About loglow

Basic Information

Statistics


Total Posts
Total Posts
122
Posts Per Day
0.05
Last Post
Teensy 4.0 Breakout Kit 10-19-2019 05:37 AM
General Information
Last Activity
10-19-2019 05:37 AM
Join Date
01-28-2013