Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • loglow's Avatar
    11-19-2019, 08:01 PM
    Yeah, it'll be interesting to see how this one goes. You'll notice that I added two white line markings onto this version of the flex cable. They're designed to align with the existing white lines on the underside of...
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-19-2019, 08:56 AM
    I changed the SD card socket. I have a feeling that some of you are going to be very happy about this. The new one doesn't have any overhang, so it should be much easier to solder. It's slimmer too. The new...
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-18-2019, 08:32 PM
    Thanks, this is great. So, what's your opinion about the ALT5 column in the PIN MUX table then? Should it be left as-is: GPIO1_IO03 GPIO1_IO02 GPIO4_IO04
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-18-2019, 08:26 PM
    Got it. Thanks!
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-18-2019, 08:25 PM
    Adobe Illustrator :)
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-18-2019, 07:04 AM
    An updated pinout card for the new revision. PDF:
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-18-2019, 04:23 AM
    PM'd both of you. Thanks! You won't have to order any parts. They'll be included :D
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-18-2019, 04:20 AM
    I think it will be easiest to solder the SD socket first, but it will also be easier now that the pads are longer too. I'm going to do some experimenting. This round will have step-by-step assembly instructions (with...
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-17-2019, 08:23 AM
    With the re-ordered USB host pins and the added second (USB host power) switch:
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-17-2019, 06:21 AM
    Yikes! I totally forgot about this. Now I remember why those two GND pins were next to each other. I've put them back in order. The TPS2055A does have an EN pin, and I just had it connected to VIN. But... What...
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-17-2019, 03:40 AM
    Ok! So, in preparation for ordering a new batch, I made some more changes: Replaced the TPD3S014 chip with the TPS2055A chip, as requested, which is larger and should be easier to solder. Added pads for the...
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-16-2019, 10:25 PM
    Sounds great, thanks very much!
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-16-2019, 10:24 PM
    Sounds great! Yes, I'll include a socket kit too. Probably not, since the previous A3 revisions were never manufactured. This will stay at A3 until fab'd. Great to hear!
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-16-2019, 09:21 PM
    I'm not sure about this change, and even less sure after reading the response by @KurtE ... This is a great suggestion, and I've updated the chart! PDF: Low-res raster preview image:
    296 replies | 18143 view(s)
  • loglow's Avatar
    11-16-2019, 08:06 PM
    Hi there everyone! Sorry for the extended time away. My life got very busy for a moment there. I haven't forgotten about this project though, and I think we're getting very close to a release! First of all, I've seen...
    296 replies | 18143 view(s)
  • loglow's Avatar
    10-19-2019, 06:37 AM
    Hi everyone, I haven't been nearly as responsive here as I'd like to be, since I've had a lot going on over the last several weeks, some of which was unexpected. I'll be on a train with Wi-Fi (hopefully) for at...
    296 replies | 18143 view(s)
No More Results
About loglow

Basic Information

Statistics


Total Posts
Total Posts
137
Posts Per Day
0.05
Last Post
Teensy 4.0 Breakout Kit 11-19-2019 08:01 PM
General Information
Last Activity
12-04-2019 09:04 PM
Join Date
01-28-2013