Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • ETMoody3's Avatar
    01-23-2020, 02:10 AM
    Yup, everything works. USB Host worked with every device tested.
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    01-22-2020, 11:20 PM
    I decided I wanted to try a breakout on a project so I went ahead and did this much assembly...no CAN bus parts, no pull ups. I used solder paste and a heat gun. Small bits of copper tape were used to hold down the...
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    01-15-2020, 11:21 PM
    The question seems clear. The functionality this user is concerned with is 4 posts above. It is USB audio for the Teensy 4, a model getting plenty of press in "maker circles" about its speed and capability, but...
    30 replies | 1020 view(s)
  • ETMoody3's Avatar
    01-14-2020, 10:08 PM
    Oh yeah, lots of noise out there in regards to ESP32. Wear waders. I like the dual core possibilities. For the most part, the arduino core is very much the same for the gazillion variant boards. When in doubt, choose...
    12 replies | 300 view(s)
  • ETMoody3's Avatar
    01-11-2020, 11:43 PM
    Linux mint 19.3 "Tricia", Arduino 1.8.10, T4 final beta hardware. Getting "Error when uploading sketch" warning, but the sketch actually uploads and appears to execute. This occurred with "usbMidi...
    30 replies | 1020 view(s)
  • ETMoody3's Avatar
    01-01-2020, 03:42 PM
    I'm no expert, but after some trial I set the temp to 20 degrees c above the solder paste temp and leave the flow low. Remains to be seen if I'll damage the gun that way, the temp is at the low end of the gun's range...
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    01-01-2020, 03:04 PM
    Yes, that's the plan, more or less. I have some MG Chemicals heat cure adhesive on the way to make sure nothing gets dislodged doing things in steps. ...
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    12-31-2019, 04:17 PM
    I'm waiting to test your assembly instructions. I'll be using a preheater and heat gun to solder the surface mount stuff. If you happen to have pre-printing data available, that will work just fine.
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    12-15-2019, 06:05 PM
    No issues as with 1.49 b2
    45 replies | 2949 view(s)
  • ETMoody3's Avatar
    12-15-2019, 03:49 PM
    Replacement boards only, thanks
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    12-13-2019, 01:57 AM
    Yeah, I'm seeing exactly what Defragster is describing. Looks like the error may only be on the flex cable?
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    12-12-2019, 05:33 PM
    Received, much thanks. Ordering extra T4 boards Friday. Will likely wait until detailed instructions are available so as to test those as well. I do have a usb microscope.
    406 replies | 25145 view(s)
  • ETMoody3's Avatar
    12-10-2019, 07:21 PM
    attached T4 previously flashed with "Keyboard Simple" sketch to windows 10 notebook computer. It rebooted, and failed to acknowledge the built in keyboard. Another reboot corrected this. A second attempt to...
    44 replies | 1979 view(s)
  • ETMoody3's Avatar
    12-10-2019, 07:11 PM
    Installed on linux mint 19.2 Tina, XFCE desktop, Arduino 1.8.10 USB Midi example " InputRead " works as expected. USB Keyboard example "Simple"... "all hell" breaks loose. Random applications launched, ' Start...
    44 replies | 1979 view(s)
No More Results
About ETMoody3

Basic Information

About ETMoody3
Location:
New Ulm, Mn

Statistics


Total Posts
Total Posts
96
Posts Per Day
0.05
Last Post
Teensy 4.0 Breakout Kit 01-23-2020 02:10 AM
General Information
Last Activity
Yesterday 10:52 PM
Join Date
03-27-2014