Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • defragster's Avatar
    Yesterday, 11:11 PM
    Not seen this before. Combining MAC and VS Code makes it a rather unique setup. Most I know are using Windows and avoid the IDE SerMon using TyCommander. TyCommander has a thread and a github share point and can...
    1 replies | 39 view(s)
  • defragster's Avatar
    Yesterday, 11:05 PM
    It won't work to try installing an older TeensyDuino over a newer version IIRC. Either the IDE would need to be uninstalled and re-installed with a fresh version, or a ZIP copy installed and used from an alternate...
    21 replies | 453 view(s)
  • defragster's Avatar
    Yesterday, 05:33 PM
    That is correct - Always using the UNZIP method for IDE 'install' my path is : T:\arduino_1.8.14\hardware\teensy\avr\ Assuming :: Paul worked to get it in AVR path all those years back when ARM was not a standard -...
    2 replies | 61 view(s)
  • defragster's Avatar
    Yesterday, 06:35 AM
    I was hoping the link found in post #2 was there - but I didn't see it - so added a note at Web-site-could-use-a-few-updates
    6 replies | 89 view(s)
  • defragster's Avatar
    Yesterday, 06:33 AM
    On this page: pjrc.com/store/ic_mkl02_t4.html A link to this startup post info : pjrc.com/threads/64468-Teensy40-only-3-3V-power-supply Might help like it did here : Teensy-4-1-I2C-Start-up-Issue
    151 replies | 10355 view(s)
  • defragster's Avatar
    Yesterday, 02:11 AM
    You are welcome! Glad I took the time to find that post from last year - and it was relevant to the issue. I didn't check if that info was linked or posted to the 'DIY Bootloader chip' page like some others details...
    6 replies | 89 view(s)
  • defragster's Avatar
    Yesterday, 01:38 AM
    Good catch @mjs513 - I glanced over that but didn't look and see the change to show the ITCM 'padding' called out.
    21 replies | 453 view(s)
  • defragster's Avatar
    Yesterday, 12:06 AM
    With installed IDE 1.8.14 and TD 1.54.b8 For another post I just built LittleFS for T_4.1 Program Flash and all looks good and right. Did not use IDE, but used TSET and programmed with TeensyLoader and TyComm as...
    21 replies | 453 view(s)
  • defragster's Avatar
    Yesterday, 12:03 AM
    For a test run of TD 1.54.Beta8 with IDE 1.8.14 I opened up :: T:\arduino_1.8.14\hardware\teensy\avr\libraries\LittleFS\examples\LFSintegrity\LFSintegrity.ino Changes: Only uncomment this line in the group :...
    6 replies | 139 view(s)
  • defragster's Avatar
    05-12-2021, 06:52 PM
    Unless it is a power startup sequencing timing issue with the T_4.1's 1062 - where USB power or tied 3.3V brings it online in proper fashion. IIRC putting a 3.0V Cell level on vBat might assist with that. Paul made a...
    6 replies | 89 view(s)
  • defragster's Avatar
    05-12-2021, 06:28 PM
    Unzipped the IDE 1.8.14 - running Arduino.exe system also wanted to Block that - had to click More and Run Anyway. Ran the 'unblocked' TeensyduinoInstall_1.54_b8.exe with no issue. Not built anything yet but ...
    21 replies | 453 view(s)
  • defragster's Avatar
    05-12-2021, 05:35 PM
    Windows 10 accepted the IDE 1.8.14 download - but again is Yelling at the TD 1.54.Beta8 ... Had to explicitly ask for it to be KEPT! Then second screen repeat and then right click and 'Unblock' in properties. Not yet...
    21 replies | 453 view(s)
  • defragster's Avatar
    05-12-2021, 05:23 AM
    Indeed they have a decent stockpile of unpinned and pinned T_4.1 over 900 total
    6 replies | 237 view(s)
  • defragster's Avatar
    05-12-2021, 05:20 AM
    It is part of pending beta - there is a dedicated thread where it developed. If reading code works look into LFSIntegrity sketch. It enables one type at a time and performs various operations. Each of the...
    6 replies | 139 view(s)
  • defragster's Avatar
    05-12-2021, 12:55 AM
    Feeding the dog too fast is as bad as not feeding it in time. It seems a delay is required, and noted in the linked thread. This repository has library for watchdog - though readme is sparse the examples show...
    2 replies | 65 view(s)
  • defragster's Avatar
    05-11-2021, 05:41 PM
    oppps - didn't open the pic - thought it was a VReg test for .BB Not sure if I got one of those - ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-11-2021, 04:44 PM
    @Kurt - is that a new VR or the installed one on the PJRC.BB? What voltage does the LED stick use?
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-10-2021, 11:40 PM
    Ordered 50 of those with with Question about 'data sheet' answered :: "YES search AMS1117-3.3 with google or what ever search engine you use, LM117-33 from Texas Instruments " - $8 expected free delivery Tomorrow. If...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-10-2021, 07:57 PM
    Any of these look like a fitting replacement - not same brand: amazon.com/s?k=1A+MCP+regulator Didn't scan thread for digikey part - it that 5V output or 3.3V? Some of each in the AMZN list - some NEXT DAY...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-10-2021, 04:02 PM
    Good/Interesting the new regulator made an obvious sound change! No added Cap or anything else? Last I tried running for a failure it ran 2.5 days without locking up or doing the power off restart sequence ??? The...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-09-2021, 08:51 PM
    Great news!
    98 replies | 9346 view(s)
  • defragster's Avatar
    05-09-2021, 07:42 PM
    After a 15s Restore of the factory blink code - it takes a button press to program as it does not include USB. Generally failure like described is caused by bad code. Though Red bootloader LED and the Orange Pin==13...
    98 replies | 9346 view(s)
  • defragster's Avatar
    05-09-2021, 06:14 PM
    That should restart an ARM Teensy. This should put it into bootloader: asm("bkpt #251"); // run bootloader
    2 replies | 69 view(s)
  • defragster's Avatar
    05-07-2021, 04:10 PM
    There is a way around the appearance that : "Teensy 3.6 can have more code than a Teensy 4" See FLASHMEM here - and other memory details: pjrc.com/store/teensy41.html#memory FLASHMEM - Functions defined with...
    7 replies | 174 view(s)
  • defragster's Avatar
    05-07-2021, 08:50 AM
    Interesting Frank! For T_4.? somebody wrote an EPROM decoder/verifier sketch. Wondering if such a thing might restore FUTURE function - if not be capable of seeing/saving 'good data?
    20 replies | 441 view(s)
  • defragster's Avatar
    05-07-2021, 08:43 AM
    Glad to hear you found a solution.
    547 replies | 36474 view(s)
  • defragster's Avatar
    05-07-2021, 05:07 AM
    Not sure of the ways of on mac? How it associates and can change that ... > Plug it in holding button, perhaps on a different USB port - then upload the Serial only sketch? > Do that with a second T_3.6 (if there is...
    547 replies | 36474 view(s)
  • defragster's Avatar
    05-06-2021, 07:02 AM
    Looks to have a set of SPI interface pins : MISO, MOSI, SCK That is a different format unit - but there are threads with LORA interface that may apply
    2 replies | 101 view(s)
  • defragster's Avatar
    05-06-2021, 06:56 AM
    There is a sample delayNanos() here - claims minimum 50 ns to be expected. :: Teensy-4-0-Bitbang-FAST Haven't tried it. Did do something using CYCCNT that is 1/600MHz and it was min ~20 cycles (12 ns?) and then...
    5 replies | 137 view(s)
  • defragster's Avatar
    05-05-2021, 06:20 PM
    The INO is treated special to help use c/cpp without knowing ALL the details and make the build "work" without sweat - a very cool idea for beginners - or even quick lazy examples :) But underlying that is a real...
    28 replies | 3012 view(s)
  • defragster's Avatar
    05-05-2021, 05:50 PM
    Only the .INO gets any default provided inclusions - primarily ARDUINO.h Adding just that should work and is less obscure.
    28 replies | 3012 view(s)
  • defragster's Avatar
    05-05-2021, 04:36 PM
    Also downloaded new PersonDetect here - but not touched. I restarted the VID test on pjrc.bb last night - still running this AM ????? The image was good first thing this morning - but now gone TOPO Wanted to test...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-05-2021, 04:06 PM
    Only indication of problem is T_LC. The T_4.x shows no such problems or issues (not does any T_3.x). No issues reported with SD card either - though new faster library code replacing the function of the prior SD.h...
    20 replies | 441 view(s)
  • defragster's Avatar
    05-04-2021, 08:23 PM
    T_3.2 right? IIRC - there was a note recently about an aggressive "cut those pads on the teensy" can penetrate too deep and sever a needed power connection on the next layer. Though post #1 suggests it was...
    9 replies | 293 view(s)
  • defragster's Avatar
    05-04-2021, 06:46 AM
    With one of the 'working' T_3.2's - In the IDE do a "VERIFY" compile a simple Blink sketch with USB Type: USB. Perhaps make sure setup() has some code like this to PRINT to SerMon opened to the connected Teensy port at...
    6 replies | 129 view(s)
  • defragster's Avatar
    05-04-2021, 06:33 AM
    see this thread ...Many-TLAs-MTP-MSC-FS-SD-SDFat-LittleFS-UsbMSCFat-to-work-with-each-other-8)
    547 replies | 36474 view(s)
  • defragster's Avatar
    05-03-2021, 04:38 PM
    Well p#864 long run never stopped and never restarted! Video going Damascus/TOPO - left it that way last night the same this morning - replugged a few secs and it quickly went back to that: LP#=34 Pisr#=111423 ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-03-2021, 12:38 AM
    I should ask about your hearing if this sounds fun :) Just hoping to see what is what - oddly now with the only real change being delayed Camera .init() steps - it seems to be not reproducing prior behavior for a long...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-02-2021, 07:40 PM
    Last I reseated the Camera into 8bit connector it went in deep and straight and latched down well - and still sitting square. It would work well for those 3 or 9 hours periods in 8 bit. Though between high V and...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-02-2021, 04:13 PM
    Quick note for post #855: HM01B0_FLEXIO_CUSTOM_LIKE_4_BIT LP#=35 Pisr#=112826 lastPR=107586641 ms=38917407 ipCyc%=59.69 S5#=0 51C LP#=35 Pisr#=112816 lastPR=107586641 ms=38918407 ipCyc%=59.61 S5#=0 51C ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-02-2021, 05:17 AM
    Mike - doing 4 bit mode after long power down - made code change. DMM showing range 208 mA to 211 mA - so maybe it did drop ... though now 208-212 after 11 mins Using SDCARD - Initializing initialization done....
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-02-2021, 04:52 AM
    The board does look interesting - just need a connector. Mike - looking at the spec the worst 8 bit camera current is 1746 micro amps - not sure it would even be visible on my meter among the 4 mA drift that shows -...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-02-2021, 02:26 AM
    PJRC.BB sat unplugged ~1.5 hours Repowered and it ran this long - i.e. 2 minutes: LP#=34 Pisr#=111490 lastPR=107583967 ms=119645 ipCyc%=59.55 S5#=0 48C Coming back I see it running this long:...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 10:26 PM
    PJRC.BB - Time to fail ~3.5 hours with a bit more current draw? { 5 LEDs on 3.3V ~10 mA, and Active SDcard adding some mA's as well ) >> ~3X faster than 9+ hours yesterday This shows 75.659 minutes running from...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 09:59 PM
    Posting on the Beta 7 thread might help it get needed attention ...
    20 replies | 441 view(s)
  • defragster's Avatar
    05-01-2021, 08:43 PM
    Current PJRC.BB run from Noon looking fine since restart this long ago: LP#=33 Pisr#=111416 lastPR=107583841 ms=2575422 ipCyc%=59.25 S5#=0 53C Turned light on coming into room and it did not freak out the...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 07:50 PM
    Was this tried with Teensyduino-1-54-Beta-7 ? Seems some EEPROM change was made ... ??? If it fails with TD 1.54 b7, post a note on that thread with link to this thread
    20 replies | 441 view(s)
  • defragster's Avatar
    05-01-2021, 07:08 PM
    Mike - glad you are up and running on the ML! Going fine on BB so far at 1100 seconds with current up measurably ... I see this mono Himax VGA version from same vendor:...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 07:02 PM
    Moved T.MM back to PJRC.BB - added 5 LEDS :: int pinLEDS={26,27,28,30,31}; // Had to skip #29 as it was on by default? I had not had SD card installed lately on PJRC.BB - but did put it in. Current no change without...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 05:49 PM
    SFun.ML Runs ST-7789 same/better than ILI9341 : SPI wires to display are 4" ribbon wires to ML - then that Ribbon to the AMZN ST7789 8" wires to the device plug. > Better is that "F" does not FLASH halo around white...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 05:14 PM
    @Mike - you had some issue returning to SFun.ML the last time? Looks like TFT on ML cabled to a Ribbon I could transfer to ST7789 and see what I see - it will add 8" of wire to the 4" in place Other than...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 04:26 PM
    SFun.ML w.T.MM fine overnight run and still going at 8+ hours this run - at least an hour before that: LP#=36 Pisr#=111391 lastPR=107583781 ms=28750380 ipCyc%=59.76 S5#=0 55C LP#=34 Pisr#=111485 ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 07:45 AM
    It has been 9-10 hours of continuous runtime on PJRC.BB since the T.MM was put back on - with above noted 'Colorized' output display, and successful reprograms and running. SEE POST #819 for repro steps with code...
    888 replies | 19703 view(s)
  • defragster's Avatar
    05-01-2021, 06:57 AM
    These physical Bottom side connect details are on product page images at PJRC.COM. On T_4.0 the D+ and D- are for USB_HOST - a second USB device on the MCU, not the primary Device USB interface for programming. On...
    3 replies | 171 view(s)
  • defragster's Avatar
    05-01-2021, 12:54 AM
    Remembered to include that in p#819 - currently I have #3 - 4 bit selected - though, correct mostly before it was #2. Since the odd image above - restart has been on "V" for another 2600 seconds to far without issue....
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 11:31 PM
    Noted in p#815 : T.MM on PJRC.BB: T.MM on BB with HM_CAM, SSD1306 on i2c and included ILI9341 wired to PCB socket I was crafting email and clipped that from there and deleted email. The Sketch here is ::...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 10:14 PM
    No, on the PJRC.BB. I found noted troubles in past days keeping the T.MM working, today Kurt and Mike are seeing similar 'stumbles' ... see post 807 and 809 above. Was just doing a current check on the PJRC.BB with...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 07:08 PM
    RE image space for SD WRITE: I noted this the other day and REMOVED it from Ex_2 :: That image array is "Unused Variable" after Mike's rewrite to 'always use the latest image in another buffer' IIRC. >> That line...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 05:10 PM
    Sounds like you two are stressing the PJRC.BB VReg like I was seeing in past days? Leading to the T.MM getting faulty power and function on that breakout? > and T.MM function was failing and doing restarts ... or...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 04:57 PM
    will say again Kurt - the Video mode looks awesome :cool: One thing I saw on the T.MM Blue 13==LED, during VID I'm not seeing BLUE, unless the 't' is on. Not sure that is a bad thing - just interesting the...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 07:00 AM
    Just did the lights ON>OFF a couple times and the image I saw must have been a one time 'odd mode'. Through now just ceiling light - earlier the window behind me was outside daylight as well and it didn't go off :) ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 06:20 AM
    The noted 'white area flash' is just a pulsing of the bright white of the overhead light and bright area on the "F" frame changes. Not at all like that in "V" mode. Ran fine a long time as "V" with 't' - using:...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 02:54 AM
    It hangs the code to stop "V" then do an 'f'. Restarted "V" and waited this long to start 't': * continuous mode (Video) started LP#=61178 Pisr#=1 lastPR=0 ms=1672503 ipCyc%=0.00 S5#=0 57C ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-30-2021, 01:57 AM
    Tremendous Improvement in VIDEO!!!! >> #define _hmConfig 2 // select mode string below >> #define MMOD_ML 1 isrPrime_it.priority(144); //isrPrime_it.priority(122); hm01b0.setVSyncISRPriority(102); ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 11:49 PM
    okay, no rush - back in an hour - just stopped by ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 11:46 PM
    Example2 works as it did for f, F, t "V": now scrolls - still interrupts SSD box draw it doesn't have the sketch edit for the callback buffer change?
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 11:18 PM
    Odd, I recall DMA grief - jumped to 4 bit and it worked - now going back both of those working without issue with last update git code. About that SD card buffer - need top get back to trying malloc() temp buffer -...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 10:46 PM
    Did you change :: #define MMOD_ML 1
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 10:43 PM
    Github is Lame - only Kurt has it mastered. Though with No Permission to MJS513 - I think I found the key for switching base repository in 'Repository Settings' ... but merging is very unclear When I went back to...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 10:11 PM
    That 'no 1.8V enable' would explain the scanner.INO not finding it
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 10:09 PM
    Seems I saw another device show on PJRC.BB - but not on the ML ??? Interesting to know if your ML finds it when you get it 'untroubled'. I'll go do some chores and look for LIB update a bit later.
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 09:39 PM
    busy1306 only from loop - noted in p#764 : "ref: SSD1306 I/O is called from loop() -> loopPR()" > I considered trying it from the _isr() but that seemed to be asking for trouble. Thanks for the LA info - good you...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 09:19 PM
    Just back here - didn't get vid update - for any new testing yet today ... Kurt - The old stuff is a hazard - so any update would be a step forward for testing.
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 06:22 PM
    If the VID mods don't end up with clean i2c to SSD ... Will be interesting to put LA on the i2c with SSD1306 and the _isr trigger lines for video. Left Ex_2 - no 't' - running "V" that showed tearing - and again...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 04:20 PM
    <uninformed questions ahead ???> Does Camera use i2c? After startup - i.e. not like PJRC Audio Board just for setup - but more often during camera read? Though scanner on the SFun.ML shows this for default "Wire":...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 03:07 AM
    Two DMM's on diff 3.3V & GND and neither jiggled at all ... self restarts and failed SSD boxes continued. Could not get a stable Button to do 15s Restore ... Moved the T.MM to SFun ML carrier - no reprogramming....
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 01:48 AM
    TOO WIERD .... IT IS BACK .... Left it running as above ... then the computer is getting and losing something on USB ??? Yep - the T.MM on PJRC.BB has started start and reboot???? LP#=1 Pisr#=59275 ...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-29-2021, 12:22 AM
    ?? - just did the PR with that line commented as that as how it was run for last p#747. >> And 'V' went bad with 't' at PRI(144) - and never recovered ... Just started an Ex_2 with _isr PRI(122) and it is working...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 11:30 PM
    Missed the add to init - yes, I see it. Assumed that was added for user discretion ... though obscure and hard to debug when it crashes :) PR done - added "V", set framerate to (30) and (60) is a fail. Put 't'...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 11:22 PM
    PRIOR run just stopped this long run with prior hardcoded PRI(102) in lib >> redraw rate = 9.43 Hz secs = 10440 deg C=52 So PJRC.MM.Breakout is up and running with Camera connector properly seated :) >>...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 07:19 PM
    The only issue I see is that PRI(128) breaks w/screen Un-Sync and Faults ... not sure what others? > ... - looking close the camera ribbon is not perfectly square - wonder it is is cross connecting and shorting...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 07:06 PM
    Ran this - not sure if it saw my cat or not - cats are not easy to present to the camera: airplane 0: 94 0: 84 0: 117 0: 40 0: 79 0: 0 automobile 1: 0 1: 0 1: 0 1: 1 1: 0 1: 0 bird 2: 2 2: 42 2: 3 2: 1 2: 1 2: 1...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 06:09 PM
    Code not shown to show play context? But is this the answer from HERE > see right pane: isPlaying(); Return true (non-zero) if playing, or false (zero) when not playing. See the note below about delayed start.
    3 replies | 156 view(s)
  • defragster's Avatar
    04-28-2021, 06:05 PM
    Have fun with digitalWrites. Exposing the priority adjustment should make that available easily enough. You mentioned pulling the needed GPIO from 6789 to the low speed individual interrupt? If that worked on the...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 04:51 PM
    Mike p#728 Test #2 is the " problem discovered with 't' " - when user _isr PRI not set lower than (128==default) - i.e. (144) > originally it was written at PRI(255) just to assure the camera code could deal with...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 04:25 PM
    T_4.0 can send data faster than the computer USB can keep up with and handle when unrestrained. ... code presented just is a snippet - assuming TimeSand is 4 byte variable? and this "arrsize" is the 25 K sample...
    3 replies | 197 view(s)
  • defragster's Avatar
    04-28-2021, 08:31 AM
    If a CONST variable of any type is passed - by definition as a constant it cannot be modified, like "data='X';". Putting the "quoted string" as a parameter makes it a constant not associated with a variable so it can...
    11 replies | 262 view(s)
  • defragster's Avatar
    04-28-2021, 08:01 AM
    T.mm running fine 2.5 hours after the last time it was reprogrammed. Multiple time before that with no issues and no restarts or hangs. This is with CORES as durrent at last post. THOUGH :: seeing this is using...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 04:31 AM
    T.MM on SFun_ML 35 minutes and all is well doing : 't' and "F" - the SSD1306 is still running as it should. - don;t have active Serial5 pins exposed on ML - so that is a NOP. >> 1 hours 20 minutes and multiple...
    888 replies | 19703 view(s)
  • defragster's Avatar
    04-28-2021, 03:08 AM
    Change that to if (1) to get "F" ALSO line ~369 back to 30 - fails on (60) :: hm01b0.set_framerate(30); //15, 30, 60, 120
    888 replies | 19703 view(s)
More Activity
About defragster

Basic Information

Statistics


Total Posts
Total Posts
13,930
Posts Per Day
6.11
Last Post
Teensyduino Serial Monitor vs VSCode and PlatformIO flashing - Fireworks! Yesterday 11:11 PM
General Information
Last Activity
Today 04:54 AM
Join Date
02-15-2015