Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • PhilB's Avatar
    Yesterday, 10:32 PM
    PhilB replied to a thread Teensy MicroMod in General Discussion
    Well, I'm not sure how strict that is. The SFE docs say you don't have to adhere to the pinouts. Honestly, the same 2x3 ethernet header on the compute board would decrease my interest level. At least with the T4.1, I...
    25 replies | 705 view(s)
  • PhilB's Avatar
    Yesterday, 09:44 PM
    PhilB replied to a thread Teensy MicroMod in General Discussion
    I wonder if, instead of the 6 pin header, all the ethernet pins (R+, R-, T+, T- and LED) go through the micromod pins. They push USB D+ and D- through them so differential pairs are possible.
    25 replies | 705 view(s)
  • PhilB's Avatar
    Yesterday, 04:02 PM
    PhilB replied to a thread Teensy MicroMod in General Discussion
    Yes, wait and see is good advice. Though, having a product based on the T4.1, I am keenly interested in this development. I think I see the potential for a pony in there.
    25 replies | 705 view(s)
  • PhilB's Avatar
    Yesterday, 02:53 PM
    PhilB replied to a thread Teensy MicroMod in General Discussion
    I have only a surface understanding of the core code so I could be wrong but looking at the github page, it appears the hypothetical micromod board would have fewer analog and digital I/O pins than the T4.1. Is that...
    25 replies | 705 view(s)
  • PhilB's Avatar
    10-23-2020, 07:53 PM
    PhilB replied to a thread Teensy MicroMod in General Discussion
    Interesting to say the least. I wonder how ethernet would be handled. Hypothetically, of course.
    25 replies | 705 view(s)
  • PhilB's Avatar
    10-22-2020, 03:55 PM
    You have a pretty steep learning curve ahead. I suggest you start with something a lot simpler than a BGA package. Assuming you want to do surface mount, you could look at doing SOIC packages, 805 Rs and Cs. The Atmel...
    5 replies | 205 view(s)
  • PhilB's Avatar
    10-17-2020, 04:43 PM
    In that case, a simple plug-in to read the voltage could be written. My breakout board has a serial port header on it so you could use that to get the tip voltage. Sounds pretty easy at first blush.
    6 replies | 380 view(s)
  • PhilB's Avatar
    10-17-2020, 03:23 PM
    A THC is in the development stages. Terje, the grblHAL developer is looking at it right now. The T4.1 has more than enough spare cycles. I'm pretty sure he would love to work with you on it. I have an ADC card in...
    6 replies | 380 view(s)
  • PhilB's Avatar
    10-17-2020, 12:46 AM
    It can use the sd card on the teensy. The best way to use it is to put the card in the teensy and leave it. If you put the machine on the network via ethernet, you can download your GCode to it and run it from there. ...
    6 replies | 380 view(s)
  • PhilB's Avatar
    10-15-2020, 10:09 PM
    I've posted about my Teensy 4.1 Breakout Board for grblHAL previously. There was some interest in seeing actual machines built with it. So,... Here is a show case of grblHAL based CNC machines with lots of details on...
    6 replies | 380 view(s)
  • PhilB's Avatar
    10-12-2020, 04:22 PM
    Yes, that doesn't need a beefy driver at all. But, I would suggest you look at the TMC step sticks. They are head and shoulders above the others. I was using a 4988 in an astro tracker I made. While it worked fine,...
    5 replies | 226 view(s)
  • PhilB's Avatar
    10-01-2020, 02:46 AM
    Yeah, all those can add up. I've seen it all except for returns. Haven't had one yet though I expect it to happen. I do a visual inspection on everything I ship so at least obvious stuff gets caught. And, I use my...
    20 replies | 555 view(s)
  • PhilB's Avatar
    09-30-2020, 06:07 PM
    Thanks. I'll look at the 2113. My Chinese assembler has them in stock so it would be easy. $10 may be a reasonable price for 1 but you should factor in your time to package and ship. Consider your net per...
    20 replies | 555 view(s)
  • PhilB's Avatar
    09-30-2020, 02:25 PM
    On your original question - is there a market for these? Definitely. You've done a lot of the hard work (including documentation!) so might as well harvest a little reward for it. Tindie is an easy way to do this...
    20 replies | 555 view(s)
  • PhilB's Avatar
    09-30-2020, 01:55 PM
    This looks well thought out. Good job. What power multiplexer are you using? I've been looking at the TPS2114/5 for a project I'm doing and have exactly the same problem of the bidirectional power pin. I thought...
    20 replies | 555 view(s)
  • PhilB's Avatar
    09-28-2020, 10:58 PM
    I'm hoping that the UGC and bCNC folks get grblHAL religion. It is capable of taking significant share from both grbl "classic" and LinuxCNC. But, to be honest, java based GCode Senders have their limitations. It...
    30 replies | 2161 view(s)
  • PhilB's Avatar
    09-28-2020, 07:48 PM
    Hi John. Have you tried grblHAL with compatibility settings? It takes a recompile though I have prebuilt 3, 4 and 5 axis versions on the github page. Or, you can build it yourself from the grblHAL github site. Follow...
    30 replies | 2161 view(s)
  • PhilB's Avatar
    09-24-2020, 03:15 PM
    Are you saying they took your exact layout and used that to build their product line? Then you may have a copyright claim against them. If you are saying they liked your idea and built a product that is very similar...
    16 replies | 429 view(s)
  • PhilB's Avatar
    09-24-2020, 02:11 PM
    There's a fine line here. Some companies do have an excessive markup on generic stuff but this race to the bottom (line) causes some real problems for electronic products. The whole "Blue Pill" for $2 thing has lead to...
    16 replies | 429 view(s)
  • PhilB's Avatar
    09-21-2020, 11:11 AM
    Some cheap servos are pretty "spikey" and can cause glitches on the power rail. Motors and digital logic don't exactly go together well. I usually try to power them from a separate source. The logic circuits in...
    16 replies | 429 view(s)
  • PhilB's Avatar
    09-08-2020, 11:33 PM
    I haven't looked this up but what is the max recommended impedance of the iMXRT1062's ADC? Good to keep the voltage divider below that. If you need a divider that goes above the max, you can use an opamp as a...
    9 replies | 483 view(s)
  • PhilB's Avatar
    09-08-2020, 09:58 PM
    vj answered the MAC question. I can confirm each one is unique (or at least the 4 I have are). To the IP addr question, if you select DHCP, you get unique IP addrs. (I think that's the default...) You can also...
    3 replies | 210 view(s)
  • PhilB's Avatar
    09-05-2020, 02:34 PM
    Yeah, the RAMPS board was never intended to drive so many steppers and, frankly, is fairly underspec'd for the total amount of power it could draw. The saving grace there is that 3D printers are not terribly demanding....
    8 replies | 389 view(s)
  • PhilB's Avatar
    09-04-2020, 11:59 AM
    Thought I posted this but it seemed disappear. The photo is pretty blurry but it looks correct. 10 mm wide. You would run a bare wire right on top of the trace and solder it at each pad where there is significant...
    8 replies | 389 view(s)
  • PhilB's Avatar
    09-03-2020, 03:32 PM
    OK, sounds good. Sizing the traces is easy - there are on online calculators for trace width based on copper thickness and current. You don't want more than a 10C temperature rise. Note that you will never get both...
    8 replies | 389 view(s)
  • PhilB's Avatar
    09-03-2020, 03:07 PM
    Hard to say without a schematic. I would regulate to 5V for the T4.0. You don't want your 5V fighting Vusb so yes, isolate. Especially if it might be 6V... How are you interfacing to the step sticks? and are you...
    8 replies | 389 view(s)
  • PhilB's Avatar
    09-02-2020, 08:19 PM
    Yes the German CNC stuff is topnotch! Uber Alles! I'm in the US though about 1/3 of my customers are in Germany. grblHAL is definitely "not your father's GRBL". The author, Terje Io, has done an outstanding job of...
    30 replies | 2161 view(s)
  • PhilB's Avatar
    09-02-2020, 07:40 PM
    Lol. There are a number of DM556 clones out there. In fact, I would be surprised if you can actually buy a real one. As soon as there is any product that sells well, the counterfeits are not far behind. They don't care...
    30 replies | 2161 view(s)
  • PhilB's Avatar
    09-02-2020, 06:00 PM
    Yes, please post your progress and feel free to contact me directly if you have any questions.
    30 replies | 2161 view(s)
  • PhilB's Avatar
    09-02-2020, 04:34 PM
    Since you have the stepper motors picked out, you should size the drivers to them. But before that, you should probably decide on what voltage you want to run them at. I'd be temped to go to 48V so need to get drivers...
    30 replies | 2161 view(s)
No More Results
About PhilB

Basic Information

Statistics


Total Posts
Total Posts
217
Posts Per Day
0.13
Last Post
Teensy MicroMod Yesterday 10:32 PM
General Information
Last Activity
Today 05:08 AM
Join Date
03-15-2016