Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • DerekR's Avatar
    01-03-2020, 01:20 AM
    @Fritz A few of us tried using the WM8731 with the T3.6 and found a whole lotta problems with the I2C communication. The link to the thread is I2C problems with Teensy 3.6 and WM8731 codec. Paul ultimately found the...
    13 replies | 335 view(s)
  • DerekR's Avatar
    01-01-2020, 04:14 PM
    A bit off topic but if you are want to improve your soldering skills, here's a video showing the SMD assembly of a new Russian SDR (software defined radio) kit. It's not a tutorial, but it shows all the SMD soldering...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    01-01-2020, 01:16 PM
    @ETMoody3 Are you going to use solder paste and just apply it without a mask, letting surface tension draw the paste off the solder mask? I've seen videos of this being done and it seemed to work well. I'm thinking...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-31-2019, 11:33 PM
    @loglow, Will you be selling spare flex-cables when the kit is released? That would make it a lot easier to replace a wonky T4 on the breakout. I know it's possible to carefully remove and replace a flex-cable (I've...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-29-2019, 01:06 PM
    @loglow - Dan, I think these are great decisions for the board assembly options. I'm sure a lot of people would be intiminated by the SMD assembly requirement. And talking of SMD soldering, there are many You Tube...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-28-2019, 06:58 PM
    Well, that was easy!!! I just specified the CS as BUILTIN_SDCARD and everything started working on both breakouts. Thanks. So it's back to the grandkids...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-28-2019, 06:33 PM
    @mjs513 - You can never have enough solder braid ;) With my old, tired, shaky hands I can't get along without it. I've just been invaded (again) by a horde of grandkids, so Teensy stuff will have to take a back seat...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-28-2019, 02:57 PM
    My first fail! I cannot get the SD card to work on either of the two breakouts! I've tried several different cards of different sizes, checked their formatting on my PC (all are FAT32), but none are recognized by the...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-28-2019, 01:26 AM
    Dan asked us to stress USB_Host stuff in our testing, but I have a small confession: I have never dealt with USB_Host software, and don't really know anything about it. Nor have I dealt with CANbus :( Can anybody...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-27-2019, 10:58 PM
    @defragster et al Here's what I think was my order of assembly of the SMD components: C5 -> C3 -> C2 -> U2 -> C4 -> U1 -> R1 -> tiny tactile SW -> flex-cable socket -> SDcard socket -> C1 . Then the other components...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-27-2019, 10:12 PM
    @defragster: Some quickie photos. (I apologize for the quality, I'm the world's worst photographer, while my wife was a professional photographer:confused:. First the two completed boards: Then front and back...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-27-2019, 07:12 PM
    Two fully functional boards now. Both worked right away. I'm a happy camper...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-27-2019, 01:58 AM
    All is good!!;) Pin 36 is functioning! I did a quick check on all the pins and all are blinking. Congratulations Dan - it was a long journey for you, but I believe you nailed it this time! Derek
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-26-2019, 09:49 PM
    It's here (in Mass)! I'm assembling as we speak...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-23-2019, 02:52 AM
    It may (?) just arrive before Xmas - seeing as we are almost neighbors. I'll get to it asap, but family arrive tonight... the house will be a complete (but wonderful) disaster for the next few days :D Happy holidays...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-14-2019, 11:11 AM
    Great work Dan! It's a beautifully designed board and I think fixing the layout is the best long term solution for you. Would it be possible to get a new complete kit + an extra flex cable since I used all the...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-12-2019, 08:47 PM
    @loglow - Dan - I hope I'm wrong but I suspect there's a mismatch in the order of the traces on the flex-cable and the pcb trace to pin 36 at the flex cable socket :( This morning I got the replacement T4...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-12-2019, 04:04 AM
    Well, I remembered that I'd seen T4's at the local electronics store (You-Do-It Electronics in Needham, MA), so I jumped in the car and got the last one! So back in business tomorrow morning. A few more comments on...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    12-12-2019, 12:12 AM
    @loglow Dan, I've assembled the new board - thanks very much for including me. It went very well, much smoother than the first Beta - took about 3.5 hours with quite a bit of time spent working out a sensible...
    405 replies | 24757 view(s)
  • DerekR's Avatar
    11-30-2019, 10:13 PM
    @robjohn... Nice looking unit. I really like the simplicity of your panel and display!! My unit(s) are still being built on protoboards with hand wiring underneath. I'll be delighted to share my control/display...
    26 replies | 1424 view(s)
No More Results
About DerekR

Basic Information

Statistics


Total Posts
Total Posts
245
Posts Per Day
0.18
Last Post
Using the I2S with Teensy4.0 01-03-2020 01:20 AM
General Information
Last Activity
01-20-2020 05:29 PM
Join Date
05-24-2016