Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • thanos's Avatar
    10-11-2018, 09:28 PM
    Ok KurtE understood,thanks.
    46 replies | 1921 view(s)
  • thanos's Avatar
    10-11-2018, 01:01 PM
    In my project i want to use two spi channels, SPI1 and SP2 at 10Mhz. They can work at the same time or i'll have to stop each channel sequentially??
    46 replies | 1921 view(s)
  • thanos's Avatar
    09-26-2018, 09:20 PM
    I changed the pin 63-->PTE5 to 63-->PTC16 without defining a new pin,but the pin PTC16 not activated. Can not "see" the pin PTC16.
    66 replies | 15486 view(s)
  • thanos's Avatar
    09-26-2018, 07:51 PM
    The example sketch Blink mux setting is not needed because the pin13=ptc5 is registered, the same i do pin64=ptc16.Why do i have to adjust the mux settings since i have set the new pin. int led = 13; // the...
    66 replies | 15486 view(s)
  • thanos's Avatar
    09-26-2018, 07:40 PM
    I tried and with digitalWriteFast but the pin ptc16 is not enabled,i measure with the multimeter 0.5v. Paul first of all, the changes i have made are sufficient or i have to do something and in other archives? ...
    66 replies | 15486 view(s)
  • thanos's Avatar
    09-26-2018, 07:16 PM
    I have set the new pin in core_pins.h and pins_tensy.c, no longer needed the mux setting. #define CORE_PIN64_BIT 16 #define CORE_PIN64_BITMASK (1<<(CORE_PIN64_BIT)) #define CORE_PIN64_PORTREG GPIOC_PDOR
    66 replies | 15486 view(s)
  • thanos's Avatar
    09-26-2018, 06:08 PM
    Can someone tell me what is wrong? Why does not work the new pin?
    66 replies | 15486 view(s)
  • thanos's Avatar
    09-24-2018, 09:02 AM
    The pcb board is already ready and i can not make any changes to the pins. The addition of new pins it can not be done?
    12 replies | 233 view(s)
  • thanos's Avatar
    09-23-2018, 09:17 PM
    Paul i will not disagree with what you said,but it is the only solution.:( On my board i have some pins which are not registered,you can help to register them?? On my thread "Teensy 3.6 diy board" (post 56) in the...
    12 replies | 233 view(s)
  • thanos's Avatar
    09-22-2018, 09:15 PM
    I tried to activate a led with a button with this code and works properly. void setup() { PORTC_PCR5 = PORT_PCR_SRE | PORT_PCR_DSE | PORT_PCR_MUX(1); PORTB_PCR2 = PORT_PCR_PE | PORT_PCR_PS |...
    12 replies | 233 view(s)
  • thanos's Avatar
    09-22-2018, 08:16 PM
    You are right,i just want to know what is wrong.:)
    12 replies | 233 view(s)
  • thanos's Avatar
    09-22-2018, 07:48 PM
    I want to read the signals from a transmitter,so i wrote the following code and read channel 1 correctly: volatile byte stick_channel_1; volatile int transmitter_channel_1; volatile unsigned long timer_channel_1;...
    12 replies | 233 view(s)
  • thanos's Avatar
    09-19-2018, 08:29 PM
    Any help please?
    66 replies | 15486 view(s)
  • thanos's Avatar
    09-19-2018, 12:39 PM
    In my question here (post 44) i have made some mistakes, i will continue on this theme. I added additionally the pin PTC16 as pin 64 in the archives "core_pins.h" and "pins_tensy.c" with the following changes and...
    66 replies | 15486 view(s)
  • thanos's Avatar
    09-18-2018, 09:48 PM
    Hello again, I added additionally the pins PTA24, PTA25, PTA27 and PTC16 in the archives "core_pins.h" and "pins_tensy.c". 1) core_pins.h i changed #define CORE_NUM_TOTAL_PINS 64 ---> 68 #define...
    46 replies | 1921 view(s)
No More Results
About thanos

Basic Information

Statistics


Total Posts
Total Posts
137
Posts Per Day
0.17
Last Post
Teensy SPI question 10-11-2018 09:28 PM
General Information
Last Activity
Today 03:50 PM
Join Date
08-12-2016