Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • dkryder's Avatar
    10-28-2019, 12:40 AM
    thank you for the info and links. i have not worked with pex but with pvc i could use a hairdryer or heat gun to shape/bend. do you have any experience or info on heating pex pipe to shape it.? in the videos it looks...
    7 replies | 160 view(s)
  • dkryder's Avatar
    10-27-2019, 10:35 PM
    i figured it was straight pipe that was needed. i'm just surprised that much light is emitted with the white. thanks for the links. does the code need to be modified based on length of pipe?
    7 replies | 160 view(s)
  • dkryder's Avatar
    10-27-2019, 10:10 PM
    never seen stuff like the last 20 sec of the video. is that the flicker? also is that clear straight pex? or the hazy? nice project.
    7 replies | 160 view(s)
  • dkryder's Avatar
    10-22-2019, 01:28 AM
    i'm not sure how much control over the content of the shared board page on OSH you have but i noticed you have a note about the .8mm on your github and something similar on the OSH board page would be a plus.
    111 replies | 4157 view(s)
  • dkryder's Avatar
    10-19-2019, 01:05 AM
    this thread has been an eye opener for me. i would have never thought that OSH would just continue churning out defective boards once they were made aware of the issue. .8mm & castellation just don't work with this pcb...
    111 replies | 4157 view(s)
  • dkryder's Avatar
    10-13-2019, 07:03 PM
    ok. but for future reference i can make a suggestion that might help. i have no idea if it would help in this case. it sounds like it would not. but ive been in similar situations when a secondary pcb was soldered close...
    111 replies | 4157 view(s)
  • dkryder's Avatar
    10-12-2019, 12:25 PM
    well since you seem to have written off that t4 you might as well try to take apart. nothing to lose. heating each pin soldered to teensy until you can pull it. gently, slightly wedge a toothpick or similar between the...
    111 replies | 4157 view(s)
  • dkryder's Avatar
    10-05-2019, 07:32 AM
    there are knowledgeable people on this forum and good tips, https://www.eevblog.com/forum/repair/
    111 replies | 4157 view(s)
  • dkryder's Avatar
    09-17-2019, 07:14 PM
    yeah. i never have done that because always afraid of hitting wrong pad accidentally. that is too close for comfort for me, but props to those who can habitually pull it off. i have hands that can be kinda twitchy at...
    13 replies | 233 view(s)
  • dkryder's Avatar
    09-17-2019, 06:56 AM
    i have a suggestion on the methodology. when using an inverted teensy/low profile headers in the testing phase it's not necessary to fully seat the teensy. i generally do at most half way. i know the teensy will...
    13 replies | 233 view(s)
  • dkryder's Avatar
    09-16-2019, 08:12 PM
    @KurtE, thanks. you are correct. i had not realized it but the flex is not optional, it's a must have. only option is host/no host and if you want host then solder flex to board OR maybe wire the T4 /breakout data pads...
    263 replies | 15665 view(s)
  • dkryder's Avatar
    09-16-2019, 05:36 PM
    i remember @loglow saying a some point that if you don't solder the flex to his data pads the host won't work yet i do not understand why i could not use maybe 30g wire from the data pads on the teensy to the data pads...
    263 replies | 15665 view(s)
  • dkryder's Avatar
    09-15-2019, 07:22 PM
    i'd suggest to remove the teensy from the breakout board if you have not already.
    263 replies | 15665 view(s)
No More Results
About dkryder

Basic Information

Statistics


Total Posts
Total Posts
55
Posts Per Day
0.05
Last Post
New CD77 Halloween Fun 2019 10-28-2019 12:40 AM
General Information
Last Activity
11-10-2019 02:32 PM
Join Date
08-26-2016