Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • Gerrit's Avatar
    Yesterday, 08:21 AM
    What would be a good solution for powering a Teensy using PoE? I came across this PoE splitter by Adafruit. Are there best practises / solutions with regards to this? Are there perhaps ethernet modules like the WIZ850io...
    0 replies | 32 view(s)
  • Gerrit's Avatar
    09-14-2018, 07:06 PM
    One of the issues with most commercially available control surfaces is the fact that they use the Mackie HUI or MCU MIDI protocol for communication. These protocols were designed to work with the 31kb/s midi bandwidth...
    0 replies | 69 view(s)
  • Gerrit's Avatar
    09-09-2018, 08:11 AM
    Gerrit replied to a thread Is this possible? in Project Guidance
    It is difficult to help without a clear understanding of what it is you want to achieve. I understand that your setup contains a guitar pedalboard and many tablets, what are the tablets for? How do these components fit...
    8 replies | 289 view(s)
  • Gerrit's Avatar
    08-30-2018, 05:20 PM
    No, not volume and pan but the parameters of the individual steps (notes). The test setup supports control of pitch, velocity, length, position and a controller for each individual step. The timing uses midi beat clock...
    28 replies | 4959 view(s)
  • Gerrit's Avatar
    08-28-2018, 03:47 PM
    i just wanna controll 8 midi motorized fader in protools i see in your code that the #define FOLLOW that is the incoming controling value and i wonder if: #define FOLLOW 0x7F from the midi out can be work on the...
    28 replies | 4959 view(s)
  • Gerrit's Avatar
    08-28-2018, 02:15 PM
    I tried that code too with the same result, the fader is jumping up and down. I guess the simplistic approach used in that code only works if you reduce the power to the fader so it will never overshoot its target....
    28 replies | 4959 view(s)
  • Gerrit's Avatar
    08-25-2018, 11:15 AM
    I was able to solve this myself, here's what I came up with: void OSCReceive(){ OSCBundle bundleIN; OSCMessage msgIN; int size; if( (size = Udp.parsePacket())>0) { byte udpData; for (int...
    1 replies | 92 view(s)
  • Gerrit's Avatar
    08-24-2018, 07:08 PM
    Working on a Teensy based OSC (Open Sound Control) controller I have a question on how to handle messages mixed with bundles. All the examples are about either bundles or messages but not both. What would be a good...
    1 replies | 92 view(s)
  • Gerrit's Avatar
    08-22-2018, 08:15 PM
    Thank you :) Using the Novation controller to test things seems like a very good idea. If it works out you can try a Teensy with a single rotary encoder to see if that works and take it from there. What I like so...
    15 replies | 431 view(s)
  • Gerrit's Avatar
    08-22-2018, 04:30 PM
    Do you have tried to control the plugin with some other midi controller and does that work? Is there are midi learn function in Protools? How are midi controllers mapped to plugin parameters? Is relative mode supported...
    15 replies | 431 view(s)
  • Gerrit's Avatar
    08-22-2018, 03:53 PM
    For the most part it depends on how much time and effort you are willing/able to invest in such a project. It is also very important to correctly understand the requirements, what you want the controller to do. Do I...
    15 replies | 431 view(s)
  • Gerrit's Avatar
    08-21-2018, 10:12 AM
    No, debouncing has to do with the way mechanical switches work. The contacts of mechanical switches literally bounce, in stead of a single switch action there're several actions in a very short time (see Bounce)....
    4 replies | 195 view(s)
  • Gerrit's Avatar
    08-21-2018, 09:38 AM
    Typical you'd use an incremental rotary encoder. How many PPR is up to you and how the DAW responds to the encoder. Mechanical (inexpensive) encoders go up to 24 PPR (96 ticks after quadrature decoding). Depending on...
    4 replies | 195 view(s)
No More Results
About Gerrit

Basic Information

About Gerrit
Location:
Maastricht

Statistics


Total Posts
Total Posts
111
Posts Per Day
0.19
Last Post
Power over ethernet (PoE) for Teensy? Yesterday 08:21 AM
General Information
Last Activity
Today 06:15 PM
Join Date
01-30-2017