Forum Rule: Always post complete source code & details to reproduce any issue!
Tab Content
  • ThijmenL's Avatar
    03-23-2020, 11:34 AM
    Hey guys, been a while. So there are also manufacturer processing boards that are used in different applications that have the imxrt1062 chip on there as well, similar to the Teensy 4.0 Do you think it's just as...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-25-2020, 08:04 AM
    Well that was quite a stupid mistake, anyway, it works now, so thank you very much, I'll keep following this forum for updates and the like. Meanwhile, I do have some questions: 1. GUISlice exports an ino file, but...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-24-2020, 08:23 AM
    Thank you, I tried to follow your instructions, yet it still doesn't seem to work for me: https://pastebin.com/raw/eu2Fqtvb The only things I change are the following: - I changed the names of the libraries from...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-23-2020, 08:01 PM
    You guys are doing amazing work that really helps me, but most likely also others out. If there's anything I could do to assist you with, that would be no problem to ask! Cheers guys!
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-21-2020, 09:33 PM
    That's okay, thanks for your efforts on this, it is much appreciated. I'll be pre-designing our GUI on paper anyway so I'll have a week or two of design on my hands nonetheless ;)
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-21-2020, 07:59 AM
    Hmm, I replaced it, even deleted the original RA8875 folder in case it caused problems, also installed it in the teensy libraries and arduino libraries folder, but then I get the warning that two libraries are existent,...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-20-2020, 04:53 PM
    So remove the RA8875 from the libraries folder, or replacing the folder with the mjs513 version? The only things i have in my libraries folder that have this string in the folder name is RA8875 and Adafruit_RA8875
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-18-2020, 08:37 AM
    For some reason I cannot get your updated version to work: https://pastebin.com/raw/B2VjcqWX
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-17-2020, 08:34 PM
    Very much appreciated, luckily we will not use the touch capabilities of the screen. I will look at your updated git repo you linked earlier tomorrow to see if I can do some work. If you're interested in what I'm...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-17-2020, 12:17 PM
    Hm yeah I looked at it, but so far nobody managed to get that to work with the Teensy 4.0, nor the RA8875 as of yet, so that's a shame. Or at least not documented.
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-17-2020, 10:42 AM
    Because power cycling is for the things I'm using it for in no way possible at all.
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-17-2020, 08:30 AM
    Okay in that case, do you know of any other GUI building application such as GUISlice Builder that could work? As I'm trying to create an interface that will not be small, it will likely take a long while to set this...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-16-2020, 08:45 PM
    I have reached a dead end, do you guys know of any other possible causes? Or simply the fact that this new processor is not properly setup in the low level code of this software? I have currently "hacked" it to think...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-14-2020, 01:49 PM
    Hmm possible, I'll see if I can find where this is located, if tweakable at all.
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-14-2020, 08:23 AM
    Unfortunately checking both files for anything that could cause problems, and tweaking those, didn't really change anything. Even the setting you spotted earlier didn't change it. I guess I'll just use the "hardcore"...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-13-2020, 10:15 PM
    That I understand, but in GUI Slicer you can also set up the width, height and dpi (dots per inch) of the screen. I'm not sure if the dpi setting influences anything.
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-13-2020, 09:42 PM
    I did not see this, thanks for your keen eye. I will try this first thing in the morning. Also, there is an DPI setting, would this, or could this affect the way the screen works? If so, I couldn't find the DPI value...
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-13-2020, 05:21 PM
    To give an update, this is how far i've come myself: This is what i created in GUI Slice Builder This is what my display shows. So technically i'm close, but also far off.
    55 replies | 1812 view(s)
  • ThijmenL's Avatar
    02-13-2020, 04:57 PM
    Hey guys, So currently I have hooked up an 4.3" RA8875 TFT screen to my teensy 4.0 and it works fine. I was just wondering if there was some intuitive program that could be used as a GUI editor, such as Qt or...
    55 replies | 1812 view(s)
No More Results
About ThijmenL

Basic Information

Statistics


Total Posts
Total Posts
24
Posts Per Day
0.31
Last Post
Teensy 4.0 + RA8875 03-23-2020 11:34 AM
General Information
Last Activity
03-23-2020 11:34 AM
Join Date
01-23-2020