OK. Following up on 446 and 446 and the "Concerning Issue" . After leaving the Teensy 4.0 unpowered since yesterday I connected it up to the laptop and got the Serial Monitor messages below and recorded four (4)...
The clicking appears to be there all the time in the earpiece whenever it is lifted. Before the message, during the message, the beep and during recording. However, one does not hear the clicking when the message is...
Excellent. I see now what you did there with the gbkcfg.txt file on the SD Chip. I finally got some sound and it played the "Greatings Earthlings" *.wav file and I got to record myself. Attached shows the files side...
Trying to edit code for risingEdge and fallingEdge and running into problems that appear to take me backwards. Will rewire my hook switch that opens on lift to close on lift to match "normal" in code and new gbkcfg.txt...
Checked my connections again. Pin 0 is confirmed as normally open contact to hook and Pin 1 is confirmed as normally open contact to momentary playback pushbutton. Modified your/our gbkcfg.txt on my SD Card Root Drive...
Checked my connections again. Pin 0 is confirmed as normally open contact to hook and Pin 1 is confirmed as normally open contact to momentary playback pushbutton. Modified your/our gbkcfg.txt on my SD Card Root Drive...
Tried loading the *40.hex file directly again. Here is the Verbose Loader.
22:04:14.103 (loader): Teensy Loader 1.56, begin program
22:04:14.458 (loader): Listening for remote control on port 3149
22:04:14.458...
Serial Monitor of COM5 shows the below message when connecting to the phone.
After 21.36.33.596 I lifted the handset. Nothing. Put the handset back. Nothing. At 21.37,30 pushed and held in momentary play message...
Teensy SD Card is showing in explorer. . Blink fast is no longer flashing on Teensy. I get one flash 6 seconds after connecting USB cable from power pack or laptop. Lift handset. Nothing. Replace handset. ...
Following up on #433 above. *.wav file was copied to SD Card along with gbkcfg.txt and SD card put back into the Audio. Opened Loader and did File/Open *.hex file and browsed to the 4.0 Hex and plugged USB in to Audio...
Thanks to Gandalf the Grubby. I have stepped away for a couple of days. But, unlike Gandalf, I am back at sundown on the 3rd day and ready to work through the night using the *.hex and tweaked *.ino from 2 days ago. ...
I unplugged the USB cable from the laptop to the Audio board and connected up a portable power supply to the board and it appears that the Blink Fast is still in there. Am I supposed to suck Blink Fast out of there...
Verbose Loader keeps beeping and providing the below "Verbose Information". Over and over again for about 5 minutes.
23:50:41.545 (loader): HID/win32: vid:8087 pid:0A1E ver:0200
23:50:41.554 (loader): HID/win32: ...
Back at it again. Ran the same verify this evening and it compiled and when it brought up the loader I pushed the button on the Teensy and this is all I see.
Warning: Board arduino:avr:teensy40 doesn't define a...
Excellent guidance. I may have succeeded. I deleted everything and even deleted them from the Recycle BIN. Could not reboot since the wife has 30 folders open in Chrome. *%### Amazon!
Extracted all of the...
In response to #422 above I went to File/Preferences and checked the Verbose when compiling box and got the error message below.
C:\Arduino\arduino-1.8.19\arduino-builder -dump-prefs -logger=machine -hardware...
Thanks for the links and lesson in structure for the various folders. As mentioned above I deleted everything and started over by downloading the 1.8.x zip files.
The IDE program is now in...
I stand corrected, it is 2.2.1 Thanks for the suggestions. I will save some of my files and uninstall everything and reinstall 1.8.19 only. I am not sure how I did not get MTP_Teensy in any of the "main" downloads and...
I just started the software portion of the Guestbook today and have had a hard time figuring out the correct steps for downloading the various IDEs, libraries. Etc. I was hoping to start with the November 4th...
Find latest posts