Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: mjs513

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Morning Ok here is something that we can use for...

    Morning
    Ok here is something that we can use for resetting at Panic Temp and high/low temp. The ISRs for Temp are interesting. Low temp is always fired, High temp fired when high temp is reached...
  2. Have another issue now that I am trying to sort...

    Have another issue now that I am trying to sort out. If both the Panic and High temp are not both in isr's the T4 resets before Panic temp is tripped unless i have a coding problem - think i am...
  3. Just a quick note: I just tested something and...

    Just a quick note: I just tested something and once the interrupt bit is set its set. I can't seem to clear it. Going to do a work around tonight but tied up with other things right now.
  4. @Frank B, @defragster, @tonton81 here a slightly...

    @Frank B, @defragster, @tonton81
    here a slightly modified version that follows @Frank B's flowchart which is probably a better way to go:
  5. Ok try this - probably could be simplier for high...

    Ok try this - probably could be simplier for high temp:
  6. Replies
    37
    Views
    1,710

    Sticky: Hard to help debug since we do not know what your...

    Hard to help debug since we do not know what your hook up is for a sd card reader. Are you hooked up to SPI or using SPI1 etc. Or what your wiring looks like. Did you remember to change the CS pin...
  7. Replies
    1
    Views
    24

    Not Sure what something like this is - did you...

    Not Sure what something like this is - did you forget to post something?

    But the answer to your question is yes it is entirely possible using the USBHost_t36 library that is installed with...
  8. @defragster - @Frank B Finally had a chance to...

    @defragster - @Frank B
    Finally had a chance to do some work on the tempMon again. Yes, Frank, tempmon now resets when the panic temp is hit.

    So using some code I modified from @defragster's...
  9. Replies
    3
    Views
    66

    Really cool that you got all three WDT's working...

    Really cool that you got all three WDT's working in a library format will play with it soonish.
  10. Replies
    173
    Views
    31,248

    To be honest why not just leave the config stuff...

    To be honest why not just leave the config stuff in the sketch - its pretty much there now the way its done in the SDFat-beta examples.
  11. Replies
    173
    Views
    31,248

    Funny - discovered that as well and we (@KurtE...

    Funny - discovered that as well and we (@KurtE and me) use it in the font_files so we don't have to keep editing them for which library is active, example:

    #if __has_include(<RA8875.h>)
    #include...
  12. Replies
    173
    Views
    31,248

    Yes that is what is showing for me as well.

    Yes that is what is showing for me as well.
  13. Replies
    173
    Views
    31,248

    @luni Took @defragster's approach for SDFat.h. ...

    @luni
    Took @defragster's approach for SDFat.h. I just made a copy and renamed it SDFat-beta.h otherwise probably won't work if you want to use it other apps.

    As for boards.txt, that is probably...
  14. Replies
    173
    Views
    31,248

    @WMXZ Just tried it using loglow's breakout...

    @WMXZ
    Just tried it using loglow's breakout board and works like a charm on Win10x64 machine once I reread everything :) Great job.

    UPDATE: copied the 1062RM to the sd card ~30Mb in about a...
  15. Replies
    173
    Views
    31,248

    Yeah - just found that now when I started poking...

    Yeah - just found that now when I started poking around :) uncommented now getting a couple of other errors:

    For SDFatBeta 0 and SDIO 1:

    D:\..\..\Arduino\libraries\MTP\MTP_Storage.cpp:92:12:...
  16. Replies
    173
    Views
    31,248

    Morning all Just downloaded the library at 727am...

    Morning all
    Just downloaded the library at 727am EST (just for ref) and followed instructions in post #118. Made one change to specify using SDIO as opposed to SDfat-Beta lib. Selected MTP...
  17. @defragster Been so long now have to go see...

    @defragster
    Been so long now have to go see where I could of put that. Was just looking at the manual - chap15(PMU) pg1234, chap13(pg1185). When panic temp is hit irq_64 should be triggered. So...
  18. Its been so long now since I read the overtempt...

    Its been so long now since I read the overtempt seq but I do remember that when a reset triggers the T4 sets a register value for overtemp and was wondering at the time if we could then use that to...
  19. Replies
    21
    Views
    783

    @JNivard Sorry for the delay. Never used one of...

    @JNivard
    Sorry for the delay. Never used one of those at 1/1000mm resolution before but it should work. Remember that the T4 is 3.3v not 5v. I used a level shifter for that. If you try it let us...
  20. @Frank = thanks just forked it and copied into my...

    @Frank = thanks just forked it and copied into my libraries folder. Will definitely come in handy.

    Hate to bring up a really old issue. But... now that reset is working temp monitor will now...
  21. Replies
    254
    Views
    5,500

    @KurtE Just incorporated the PR. Thanks. 4am...

    @KurtE
    Just incorporated the PR. Thanks. 4am here and finally playing catch up
  22. @Frank B Know I am late to game here - got side...

    @Frank B
    Know I am late to game here - got side tracked. But really like this so don't have to keep update imxrt-size and the ide:)

    Do you think it could be converted into a freemem_t4...
  23. As added FYI. The T4 HW Quad Encoder does have a...

    As added FYI. The T4 HW Quad Encoder does have a glitch filter that gives you some leeway for false signals. For more info on the Quad encoder you can check chapter 55 of the IMXRT1062 Reference...
  24. Replies
    20
    Views
    210

    @KurtE Nice work on the timer. :) I did a...

    @KurtE
    Nice work on the timer. :)

    I did a modification to the FRAM lib to write any number of bytes but its not working, can confirm this without the i2csniffer but I hooked it up any way with...
  25. Replies
    20
    Views
    210

    Tim-that's actually using @KurtEs original form...

    Tim-that's actually using @KurtEs original form for current_portB. If I update the sketch to post #13:

    3401: Waiting for Data...
    3601: Waiting for Data...
    3801: Waiting for Data...
    3868...
  26. Replies
    254
    Views
    5,500

    Ok just pushed up a change to my WIP_display_font...

    Ok just pushed up a change to my WIP_display_font branch (same as master branch): https://github.com/mjs513/RA8875/tree/WIP-display-fonts that may work.

    In settings at about line 87 you can select...
  27. Replies
    20
    Views
    210

    For the fun of it I hooked it up a T4 running my...

    For the fun of it I hooked it up a T4 running my FRAM test sketch and got the following which shows reading and writing to the FRAM. This is after the change to the Wire buffer lenght.


    1801:...
  28. Thread: TeensyTimerTool

    by mjs513
    Replies
    81
    Views
    1,093

    @luni Thanks for checking. As you said at the...

    @luni
    Thanks for checking. As you said at the results are consistent when you use the tight while loop.

    By the way it really is a great lib you put together. One question I have is if there...
  29. Replies
    254
    Views
    5,500

    @KurtE You beat me to it - just took a look....

    @KurtE
    You beat me to it - just took a look. There's 2 or three places it would have to get changed so you could specify which bus to use. You already identified one. The other is about line 571. ...
  30. Thread: TeensyTimerTool

    by mjs513
    Replies
    81
    Views
    1,093

    Sorry I am late to the party here. I've used c++...

    Sorry I am late to the party here. I've used c++ atomic's when I was using teensythreads and they worked great. I did try the following this morning:

    #include "TeensyTimerTool.h"
    using...
  31. Replies
    13
    Views
    160

    Just a couple of quick comments. 1. As...

    Just a couple of quick comments.

    1. As @KurtE pointed out if you want to use a T4 you have to change from using i2c_t3 to the normal Wire library. Otherwise it will never compile.
    2. The...
  32. Just reran the sketch and got the exact same...

    Just reran the sketch and got the exact same results as I Posted prior: 432Mhz using:

    #elif defined(__IMXRT1052__) || defined(__IMXRT1062__) // Teensy 4.x
    #define ILI9341_SPICLOCK 60000000u ...
  33. Replies
    13
    Views
    134

    I think this is an equivalent version:...

    I think this is an equivalent version:...
  34. Replies
    13
    Views
    134

    Well, if the scanner is not identifying the...

    Well, if the scanner is not identifying the BMP280 the only possibilities I can think of are:
    1. You wiring is wrong - you didn't show the pinouts for the board or your wiring connections
    2. You...
  35. Replies
    254
    Views
    5,500

    Thanks to @KurtE, Autocenter is now operational...

    Thanks to @KurtE, Autocenter is now operational for the ILI9341 and the GFX fonts as well. Enjoy.
  36. Replies
    13
    Views
    134

    I don't see any pin outs on the board - are you...

    I don't see any pin outs on the board - are you sure you have the right connections to sda/scl
  37. @skpang Haven't really used the Adafruit library...

    @skpang
    Haven't really used the Adafruit library so no sure. But have you tried the ST7735_t3 library that is installed with Teensyduino. SPI Clock is set in one place, ST7735_t3.h, right at the...
  38. Replies
    254
    Views
    5,500

    @neurofun - @KurtE Just pushed a fix for...

    @neurofun - @KurtE
    Just pushed a fix for autocenter. Let me know if you still have problems. Right now autocenter will only work for default fonts.
  39. Replies
    254
    Views
    5,500

    Will check it out. Thanks for testing

    Will check it out. Thanks for testing
  40. Replies
    254
    Views
    5,500

    ILIXXX Fonts and GFX Fonts for RA8875

    Recently @KurtE and I have been working on a modification of the RA8875 library to use the ILI9xxx fonts and Adafruit GFX fonts. We have finished our initial implementation of modifications to the...
  41. Replies
    58
    Views
    4,543

    @tannewt I had a chance to install the .hex on...

    @tannewt
    I had a chance to install the .hex on the T4 the other day using the Teensy Loader to upload the file on a Windows10x64 PC. After upload Windows install it as a new drive and I was able to...
  42. Replies
    37
    Views
    1,710

    Sticky: Just installed on a Windows10x64 with no issues. ...

    Just installed on a Windows10x64 with no issues. Ran a few sketches that I was just working on: RA8875 and ILI9488 and both uploaded and worked with no problems.

    Also checked the BNO080 and...
  43. Gave it a try on the T4/ILI9488 combo with the...

    Gave it a try on the T4/ILI9488 combo with the following results:

    CS:10, DC:9 RST:8 MOSI:11, SCLK:13 MISO:12
    ILI9488_t3n: (T4) SPI automatically selected



    MOSI:11 MISO:12 SCK:13
    ...
  44. Replies
    58
    Views
    4,543

    Thanks for pointing me to it - still on first cup...

    Thanks for pointing me to it - still on first cup of coffee and eyes have closed. Will take a look. Maybe a improvement that can be made to circuit python in the future.
  45. Replies
    58
    Views
    4,543

    @tannewt One of the things I like about the T4...

    @tannewt

    One of the things I like about the T4 is the ability to overclock if I want directly from the sketch.

    Poking around your repository, there's a lot there so probably missed it, it...
  46. Replies
    58
    Views
    4,543

    @manitou Thanks for the explanation. Will...

    @manitou
    Thanks for the explanation. Will probably have to pick one of the up at some point - too many things on the to do list right now to start playing with that one. Still not sure which way...
  47. Replies
    58
    Views
    4,543

    Thanks. I posted as a comment on the video how...

    Thanks. I posted as a comment on the video how it was done so this answers that question. Did you see Paul's comment on the last 4K of memory: ...
  48. Replies
    9
    Views
    776

    Really cool project - looking forward to when...

    Really cool project - looking forward to when they publish it :)
  49. Replies
    23
    Views
    288

    Heres a couple of other references and one new...

    Heres a couple of other references and one new one:
    https://github.com/ethz-asl/kalibr/wiki/IMU-Noise-Model

    https://www.novatel.com/assets/Documents/Bulletins/APN064.pdf
    ...
  50. Replies
    23
    Views
    288

    @WMXZ Thanks for posting that - used that as...

    @WMXZ
    Thanks for posting that - used that as reference in the past but couldn't find the link!
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4