Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: PaulS

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. You're welcome. Happy to hear the LC is still OK....

    You're welcome. Happy to hear the LC is still OK.
    About the Vin pin: when you connect the Teensy LC with a USB cable to a PC, the output voltage on that Vin pin will be the USB 5V. You can pull...
  2. It looks like you connected the 5V of the...

    It looks like you connected the 5V of the joystick to the Vin pin of the Teensy LC.
    Please connect it to the 3V3 pin of the Teensy LC.
    The Teensy LC pins are only 3V3 rated...hope the board and/or...
  3. Replies
    9
    Views
    171

    Looking forward to your creation! Paul

    Looking forward to your creation!
    Paul
  4. Replies
    9
    Views
    171

    You have to add a potmeter yourself with the...

    You have to add a potmeter yourself with the aliexpress pedal though...
    "The notched wheel is not in the right format for the Dunlop potentiometer" according to the comments.

    Paul
  5. Replies
    9
    Views
    171

    Or even cheaper and stereo:...

    Or even cheaper and stereo: https://www.thomann.de/de/lead_foot_lfv2.htm
  6. Replies
    9
    Views
    171

    What about this one:...

    What about this one: https://www.thomann.de/de/lead_foot_lfx1.htm?
    Or this one: https://www.thomann.de/de/lead_foot_lfv1.htm

    Paul
  7. Just did a quick test with a joystick and Teensy...

    Just did a quick test with a joystick and Teensy LC:

    24674

    Ran the basic example and executed joy.cpl on Win10:

    24675

    All looks good.
    Paul
  8. Allright. Did you try another joystick? What kind...

    Allright. Did you try another joystick? What kind of joystick are you actually using?

    Paul
  9. Between screen and keyboard there is usually...

    Between screen and keyboard there is usually little room; did you mean between chair and keyboard?

    On topic now: for debugging it's best to strip down the code to the bare minimum, test it and...
  10. Replies
    2
    Views
    163

    When you run the I2C_scanner program on the...

    When you run the I2C_scanner program on the Teensy, you won't find its I2C address because the Teensy acts as the I2C host. The I2C scanner only detects I2C slaves.

    Regards,
    Paul
  11. Replies
    8
    Views
    220

    I think I know where the confusion comes from:...

    I think I know where the confusion comes from: long time ago I was tought at school this:
    24594

    The curved line on the polarized cap indicated the negative pin.

    Agree, an explicit '+' sign is...
  12. Replies
    8
    Views
    220

    I'm pretty sure that the 100nF cap mounted on the...

    I'm pretty sure that the 100nF cap mounted on the board, shown on this page, is not a polarized version. A 100nF ceramic cap will suffice here.

    Paul
  13. Replies
    14
    Views
    538

    Thanks Rolf, You might be interested in the...

    Thanks Rolf,
    You might be interested in the measurements I did as well on several DAC's.

    Paul
  14. Replies
    14
    Views
    538

    Hallo Rolf, Thanks for your reply. I was...

    Hallo Rolf,
    Thanks for your reply. I was wondering what A/D-converter you were using for your measurements. Some USB audio device?

    Paul
  15. Replies
    14
    Views
    538

    Hallo Rolf, Just curious: what measurement...

    Hallo Rolf,
    Just curious: what measurement program did you use and what ADC?

    Danke,
    Paul
  16. Thread: I2S on Teensy4.1

    by PaulS
    Replies
    3
    Views
    281

    Most probably yes. But you can easily verify that...

    Most probably yes. But you can easily verify that by commenting out the line filter1.frequency(30); // filter out DC & extremely low frequencies and check again with Audacity.

    Paul
  17. Thread: I2S on Teensy4.1

    by PaulS
    Replies
    3
    Views
    281

    Maybe this...

    Maybe this post helps?

    Paul
  18. Replies
    41
    Views
    2,458

    Hi Manitou, what voltage do you power the DAC...

    Hi Manitou, what voltage do you power the DAC board with: 3V3 or 5V?
    The board you referred to should be powered by 5V.

    Paul
  19. MISO1 is actually brought out on the Teensy 4.0....

    MISO1 is actually brought out on the Teensy 4.0. Just below the card on this page, it states "Not shown on this reference card, Pin 0: CS1, Pin 1: MISO1"

    24298

    Paul
  20. Replies
    205
    Views
    14,960

    First unofficial Arduino IDE support for the...

    First unofficial Arduino IDE support for the Pico: YouTube and on Github.
    From the video:

    24204

    @3m31s: "And as last time, the Teensy 4.1 is in a different class" :cool:

    Paul
  21. Replies
    2
    Views
    1,050

    This (https://github.com/peregrine-developments)...

    This was the first hit when I googled for "Peregrine Developments".
    Is that what you are looking for?

    Paul
  22. Hi Kevin, Your wiring diagram "Attachment...

    Hi Kevin,

    Your wiring diagram "Attachment 24027" does not show up:

    Paul
  23. Replies
    3
    Views
    250

    Whether those dinosaur versions are supportive of...

    Whether those dinosaur versions are supportive of x64, I don't know. Perhaps the quickest way to find out is to install those old versions and try it out?

    Regards,
    Paul
  24. Replies
    3
    Views
    250

    Yes, it does. Until recently, I ran Teensyduino...

    Yes, it does. Until recently, I ran Teensyduino on Windows 7 x64 Pro before upgrading to Windows 10.

    Regards,
    Paul
  25. Replies
    18
    Views
    635

    Here is another interesting video:...

    Here is another interesting video: https://www.youtube.com/watch?v=_PfUEnkqeOs

    Both reviewers had not noticed though that this yellow board has the cinch jacks reversed. The jack with the red...
  26. Replies
    18
    Views
    635

    The board...

    The board I referred to has 3 voltage regulators: the charge pump [pin 1] is powered separately, not interfering with the analog power.
    Also the 1000uF caps at the output of the 3V3 regulators is a...
  27. This strongly suggests that the button input pins...

    This strongly suggests that the button input pins on the 5V Device are pulled up to 5V and that an external button [or a Teensy pin in your case] pulls that line low. Problem is that this 5V pullup...
  28. Replies
    31
    Views
    1,040

    @MichaelM, I think you mean the SN74AHCT125N...

    @MichaelM, I think you mean the SN74AHCT125N part, isn't it? The one with TTL level input [VIH = 2V].
    The non-T part has an VIH of 3.85V at 5.5V VDD.

    Regards,
    Paul
  29. Hi Andy, Only in case a peripheral wants to...

    Hi Andy,

    Only in case a peripheral wants to drive a signal higher than 3V3 to the Teensy.
    For your application, CS, MOSI and SCK are all outputted by the Teensy at 3V3 max so no problem in that...
  30. Replies
    31
    Views
    1,040

    Hi Jim, (1) SPI always uses push-pull pins. (4)...

    Hi Jim,
    (1) SPI always uses push-pull pins.
    (4) I don't see a problem, the chip can be used for SPI, see this product.
    (5) the chip is bi-directional, it just "voltage-translates" signals from one...
  31. Replies
    4
    Views
    245

    Allright. Glad you got it to work. Regards,...

    Allright. Glad you got it to work.

    Regards,
    Paul
  32. Replies
    4
    Views
    245

    Since you are soldering on the backside of the...

    Since you are soldering on the backside of the Teensy 4.0: you did not accidently short pin 32 [HC-05 enable] to one of the SPI pins 10, 11 or 12?

    Regards,
    Paul
  33. Replies
    4
    Views
    245

    You stated "The problem is that there is no...

    You stated "The problem is that there is no response from the HC-05". Well, the first thing I would do is to measure whether pins EN and EN7 are actually set HIGH by the digitalWrite's when not...
  34. Replies
    18
    Views
    635

    The board I linked to also has 2 voltage...

    The board I linked to also has 2 voltage regulators on board. I assume to generate a 3V3 analog and a 3V3 digital power supply.
    If you want an easier-to-use board, go for this one. Check out the...
  35. Replies
    18
    Views
    635

    Price versus quality, I think the PCM5102A is the...

    Price versus quality, I think the PCM5102A is the best choice. You can find boards for less than 5 US$. See here.

    Regards,
    Paul
  36. Replies
    4
    Views
    267

    Found the datasheet of the TL2796: 23855 The...

    Found the datasheet of the TL2796: 23855
    The controller has an SPI interface for configuring the display and a 16/18/24-bit RGB video interface.
    And found some Linux driver stuff on Github as well....
  37. Replies
    4
    Views
    267

    The Alibaba page you linked mentioned "D-IC...

    The Alibaba page you linked mentioned "D-IC Built-in D53E6EA8805". Searching for that led me to this panel: Samsung AMS326P01.
    Samsung panel datasheet here.
    The driver chip is from Magnachip, part#...
  38. I verified your sketch on a T4.1 and with or...

    I verified your sketch on a T4.1 and with or without the analogRead(randomVar ); line, it shows a serial USB device [COM port].
    Did you set Menu > Tools > USB Type to Serial?

    Using Arduino 1.8.13...
  39. Replies
    2
    Views
    165

    Generally, for strips having more than 3 DotStar...

    Generally, for strips having more than 3 DotStar LEDs, you want to power that strip externally. You don't want the propshield board [or the Teensy Vin pin] to supply significant current to DotStar...
  40. Replies
    14
    Views
    591

    Great! [nice demo to show appreciation, haha]...

    Great! [nice demo to show appreciation, haha]
    What was the issue in the end? Was it indeed an SH1106 controller on the 1.3" OLED?

    Regards,
    Paul
  41. Replies
    9
    Views
    492

    Other Dutch resellers like Antratek and Floris...

    Other Dutch resellers like Antratek and Floris always shipped Teensy's to me with a card [but I never ordered a T4.0 from them]

    Paul
  42. Replies
    14
    Views
    591

    When searching further about the difference...

    When searching further about the difference between an SSD1306 and a SH1106, I saw some display pictures looking very similar to your picture in message #4.
    Here is such a thread.
    And another...
  43. Replies
    14
    Views
    591

    Looks OK to me. Could it be that your 1.3" OLED...

    Looks OK to me.
    Could it be that your 1.3" OLED has a different controller, like the SH1106? [I see 1.3" OLEDs offered with that SH1106 controller]
  44. Replies
    9
    Views
    492

    Same here with Tinytronics, no card with the...

    Same here with Tinytronics, no card with the Teensy 4.0. But never bothered to call them...
    Paul
  45. Replies
    14
    Views
    591

    Allright, no I2C pullups apparently. So you...

    Allright, no I2C pullups apparently.
    So you know what to do I guess? See this post.

    Paul
  46. Replies
    14
    Views
    591

    Allright. Now it's time to measure whether...

    Allright. Now it's time to measure whether pullups are present the I2C lines.
    With the display disconnected from the Teensy, measure with an ohm-meter between the SDA pin and GND and between the SCL...
  47. Replies
    14
    Views
    591

    You also may want to try to run at a lower I2C...

    You also may want to try to run at a lower I2C clock frequency:

    Adafruit_SSD1306 display(128, 64, &Wire, -1, 400000);

    Paul
  48. Replies
    14
    Views
    591

    I would not be surprised if the 1.3" display is...

    I would not be surprised if the 1.3" display is on another I2C-address. The zero ohm resistors near the 4 pin connector are differently strapped.
    Did you run the I2C scanner example sketch on both...
  49. Hi Bruce, you may consider buying a cheap CANbus...

    Hi Bruce, you may consider buying a cheap CANbus analyzer like this one. This device saved me a lot of time while implementing & debugging a wireless CAN bus.
    Here is a thread with some screenshots...
  50. Replies
    24
    Views
    1,024

    The datasheet...

    The datasheet of the CirrusLogic CS4272 specifies group delay for the both the ADC and DAC circuitry.
    This 24bit/192kHz codec is used in the Focusrite Scarlett 2i2 3Gen USB audio interface.

    Paul
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4