Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: DaveAK

Search: Search took 0.00 seconds.

  1. Replies
    190
    Views
    15,297

    I have a similar situation, but I believe my bus...

    I have a similar situation, but I believe my bus is correctly terminated. For me everything hangs when I inject messages over serial to be written to the bus. Reading from one controller and...
  2. Replies
    2
    Views
    132

    Anyone got any suggestions? I'm favoring the...

    Anyone got any suggestions? I'm favoring the relay approach right now, because I just don't know enough about transistors.
  3. Replies
    167
    Views
    62,928

    Looks like you've got some good answers already. ...

    Looks like you've got some good answers already. I don't know if Can0.setListenOnly should go before or after the Can0.begin, but I'm sure the setup routine is where I'd put it. One thing I notice,...
  4. Replies
    167
    Views
    62,928

    From the flexcan.h header file: Looks like...

    From the flexcan.h header file:


    Looks like listen only is not yet implemented. I don't know about your specific implementation but you can probably get away with normal mode and just not write...
  5. Replies
    2
    Views
    132

    Switching of signal lines

    I'm working on a CAN bus sniffer/splitter/injector based around the Teensy 3.6 (might move to the Teensy 4.0 for final device). As it stands it's working fine in prototype form, and I'm ready to...
  6. Replies
    190
    Views
    15,297

    Perfect! Thanks!

    Perfect! Thanks!
  7. Replies
    190
    Views
    15,297

    Running in to an issue setting msg.seq - compiler...

    Running in to an issue setting msg.seq - compiler is throwing an error say CAN_message_t is read-only:

    My code:

    void relayFrame(const CAN_message_t &frame) {
    // Take incoming frame and send...
  8. Replies
    6
    Views
    155

    Hey Antonio, I ran in to an issue that I posted...

    Hey Antonio, I ran in to an issue that I posted to your IFCT thread so that it's available to all who might be following it.
  9. Replies
    6
    Views
    155

    Taking a look at this now and it looks pretty...

    Taking a look at this now and it looks pretty straightforward. If I'm wanting strict FIFO read and writes I should just enable FIFO with interrupts/disable mailboxes on the read side and then I can...
  10. Replies
    6
    Views
    155

    I was hoping for a library solution rather than...

    I was hoping for a library solution rather than rolling my own. Right now I'm using CollinK's library, but I know you've written one with FIFO. Last I looked it was only for a single CAN...
  11. Replies
    6
    Views
    155

    FlexCAN timestamp limitations

    I'm building a Teensy 3.6 based CAN bus sniffer/splitter/injector and would like a good timestamp solution, but the provided timestamp just doesn't seem up to the task. Could anyone validate my...
  12. Replies
    2
    Views
    72

    Hey Paul, here's the debug output. The...

    Hey Paul, here's the debug output. The manufacturer, product and serial number all appear correct. I'm using the SerialTest sketch and just modified the baud rate to 9600. The device streams data...
  13. Replies
    2
    Views
    72

    Quick Teensy 3.6 USB Host questions

    I've just had to cobble together a quick dynamometer DAQ using a Teensy 3.6 and have a question about the USB Host. Part of the DAQ includes a serial input of weather data through an FTDI chip. ...
Results 1 to 13 of 13