Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: Abbasi

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    213

    Thank you so much fu4711 it is working, i am very...

    Thank you so much fu4711 it is working, i am very grateful to you dear.
  2. Replies
    2
    Views
    213

    Teensy 3.2 with command line.

    Hello everyone,
    I want to download my code to teensy3.2 by using command prompt instead of Arduino IDE. I am using window7. I read the command line as given on the pjrc forum, but I did not...
  3. Thanks for your reply actually in lab view there...

    Thanks for your reply actually in lab view there is one System exec VI,
    If I have these two command lines,
    1-for the opening program from a specific location of PC
    2-upload program to teensy
    ...
  4. Run teensy3.2 with labview using command line.

    hello everyone,
    I want to run teensy3.2 through labview
    Lets say,
    I have a code of led blink saved in computer drive.
    In LabVIEW, I want to make a button, means when I press it the save code...
  5. run teensy3.2 with labview using command line.

    hello everyone,
    I want to run teensy through labview
    Lets say,
    I have a code of led blink saved in computer drive.
    In LabVIEW, I want to make a button, means when I press it the save code from...
  6. Thank you Gays, It Worked. You were right Frank,...

    Thank you Gays, It Worked. You were right Frank, the problem was with physical connections. I refresh the teensy headers and it worked... I used wire library.....
    Thank you Frank B,...
  7. 16291 Please suggest me any expert opinion...

    16291

    Please suggest me any expert opinion...
  8. First of all thank you so much for your kind...

    First of all thank you so much for your kind response.i hope this image will clear all the ambiguities .I have connected my teensy3.2 with AD5933 IC , showed in the picture. The link below is AD5933...
  9. 16275 it's circuit photo.

    16275 it's circuit photo.
  10. Now i am using wire library but its still not...

    Now i am using wire library but its still not working ,i have connected this IC with arduino using wire library its works, but when i connect teensy3.2 it does not responding, and on SCL pin i saw...
  11. this code is modified but i am using i2c_t3.h...

    this code is modified but i am using i2c_t3.h library for teensy3.2 i have already try 100kHZ but its not working...
    Is this code is correct for teensy3.2??
  12. now i am using 3.3k ohm resistor with 3.3v but...

    now i am using 3.3k ohm resistor with 3.3v but its still not responding.




    #include "i2c_t3.h"


    void setup()
    {
  13. Interfacing AD5933 with teensy3.2, I2C issue

    hello every one,
    I am using teensy3.2 i want to interface teensy3.2 with AD5933, but when i used basic scanner example of i2c_t3-master.h library, the AD5933 is not responding, i am using 5V,...
  14. Replies
    7
    Views
    337

    First thanks all of you actually i am using USB...

    First thanks all of you actually i am using USB serial for looking my result on serial monitor. And i want to interface AD5933 IC with teensy3.2. After getting frequency from serial monitor my ...
  15. Replies
    7
    Views
    337

    Serial monitor Rx interrupt

    Hello Everyone.
    I am using Teensy3.2
    I want to communicate with one IC using I2c protocol i will get value from IC and will do some alterations on it in the place of "hello world" that is...
  16. Now it's working . Thank you so much for your...

    Now it's working . Thank you so much for your kind and quick reply..
  17. Garbage value on serial monitor using teensy 3.2

    Hello every one.
    I am new user of teensy and i am using teensy3.2 i want to get float value from serial monitor but when i enter any float value it returns me accurate value but with garbage value...
Results 1 to 17 of 17