Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: tcmichals

Search: Search took 0.00 seconds.

  1. Replies
    37
    Views
    10,981

    I was looking at running a RTOS on one of the...

    I was looking at running a RTOS on one of the processors to handle I2C, SPI and some general I/O but, I don't think the interrupt controller can assign HW interrupts across processors.
  2. Replies
    66
    Views
    15,698

    I was hoping vxWorks (Intel) would release the...

    I was hoping vxWorks (Intel) would release the new RTOS for the Quark processor on the Edison along with the RTM (Reference Technical manual) documentation. I thought the goal was to run Linux on...
  3. Replies
    36
    Views
    44,037

    OK, if you have some source code I can help out.

    OK, if you have some source code I can help out.
  4. Replies
    36
    Views
    44,037

    Yes for fun; keeping up with HW/SW skills, but...

    Yes for fun; keeping up with HW/SW skills, but also using cheap receiver has only PWM outputs a PWM/PPM encoder is needed with Afro mini.
  5. Replies
    36
    Views
    44,037

    https://launchpad.net/gcc-arm-embedded But I...

    https://launchpad.net/gcc-arm-embedded But I think the standard gcc that is shipped with the install for Teensy patch will work also.
  6. Replies
    36
    Views
    44,037

    Here is a working version of baseflight ported to...

    Here is a working version of baseflight ported to Teensy3.1
    couple of bad photos
  7. Replies
    36
    Views
    44,037

    I ported baseflight firmware and had to a mod to...

    I ported baseflight firmware and had to a mod to baseflight-conifguration tool due to GPS not being installed. Which code base are you using
  8. I would sugguest using protothreads...

    I would sugguest using protothreads Also provides a simple task management.
  9. Replies
    36
    Views
    44,037

    Good looking quad, is it possible to get a parts...

    Good looking quad, is it possible to get a parts list? basic cost?
  10. Replies
    19
    Views
    7,767

    FYI, Found this board...

    FYI, Found this board http://www.pololu.com/product/2594 the draw back is wiring the USB from the board to the teensy. This way no traces have to be cut.
  11. Replies
    19
    Views
    7,767

    To clearify; make a special USB cable with a...

    To clearify; make a special USB cable with a diode inline of the +5V comining from the PC.
  12. Replies
    19
    Views
    7,767

    Is there some other way not to avoid cutting...

    Is there some other way not to avoid cutting traces? The only other way I can think of is to mod the USB cable and cut VBUS..
  13. Replies
    36
    Views
    13,765

    CMSIS for teensy 3.0

    Is there a supported CMSIS-CORE for the teensy supported by freescale?
  14. Replies
    82
    Views
    42,595

    I've start the same project using Android,...

    I've start the same project using Android, basicly a smaller version of IOIO which only requires USB host mode. Also, have updated firmware so Android can now talk to the teensy 3.0. The main...
  15. Replies
    15
    Views
    22,131

    Serial via HID

    Which example runs the HID SEREMU_INTERFACE? Is there a program for the host for this to talk to via the HID SEREMU_INTERFACE? Also, there is plans to have a simple bulk in/bulk out for USB?
  16. That was simple, need to update the udev rules.....

    That was simple, need to update the udev rules.. or run sudo ./teensy.
  17. Trying to program Teensy 3.0 using Ubuntu 12.04 (64 bit)

    I've edited the simple blink.cpp example to blink faster now trying to program the blink.hex file into the board using the Teensy (loader is version 1.07)
    The issue is the Operation, menu option...
Results 1 to 17 of 17