Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: dirk

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,411

    Thanks Paul its this possible put the pin from...

    Thanks Paul

    its this possible put the pin from output to input and its like a "open" port for the TMC2100?
    like here http://forum.arduino.cc/index.php?topic=12212.0 ?
    o the simplest way are one...
  2. Replies
    4
    Views
    2,411

    ok i research a little bit more in the mean...

    ok
    i research a little bit more
    in the mean time i was thinking using a optocoupler whit tristate output.
    but i found in a arduino forum that the guys put for the third state the pin to input.
    ...
  3. Replies
    4
    Views
    2,411

    TMC2100 Stepper Motor Driver

    Hi

    i wont control a Trinamic TMC2100 Stepper Motor Driver https://github.com/watterott/SilentStepStick/blob/master/hardware/SilentStepStick-TMC2130_v10.pdf with a Teensy 3.1
    ok
    the Pins CFG1...
  4. Replies
    8
    Views
    1,802

    ? Page 8 say i can change the Baud Rate , what i...

    ?
    Page 8 say i can change the Baud Rate , what i try.
    i change the rate
    whit something like this



    i'am confused

    Serial1 -> LCD Display (serial TX-RX) ( print only in this case )
  5. Replies
    8
    Views
    1,802

    This its for the Display -> i use Serial Tx to...

    This its for the Display -> i use Serial Tx to Rx
    its for the USB Port for example sync the RTC whit a PC, what i don't need.
    before i used Serial.begin ( only for test and learning ) like this....
  6. Replies
    8
    Views
    1,802

    Thanks Paul i use the default ...

    Thanks Paul

    i use the default
    Serial1.begin(9600);
    i try higher rates, but the display shows only crap or nothing.
    its a NHD-0216K3Z-FL-GBW-V3.
    and thanks for the tip whit the function, i...
  7. Replies
    8
    Views
    1,802

    Newbi RTC without Cristall?

    Hello
    iam not a Programmer. but learning still
    ok my questions about the RTC
    the Code works fine,
    i pulse a Steppermotor 1 Steps (pulse) in x microseconds using long (about 46714 microseconds)....
  8. Replies
    132
    Views
    76,426

    http://forum.pjrc.com/threads/26776-Teensyduino-1-...

    http://forum.pjrc.com/threads/26776-Teensyduino-1-20-Released

    https://github.com/PaulStoffregen/cores

    Works
    i can compile :-) error going
    i downloaded this...
  9. Replies
    132
    Views
    76,426

    i am locking to this...

    i am locking to this http://www.pjrc.com/teensy/td_uart.html
    and now i understand , i need use
    #define Serial7Segment Serial1 and pin 1 TX.:cool:
  10. Replies
    132
    Views
    76,426

    @ Nantonos your men something like this? ...

    @ Nantonos

    your men something like this?

    http://forum.pjrc.com/threads/26567-Sparkfun-LCD-module-w-daughter-board?highlight=hardware+serial




    Iam a non Programmer :-( and i try the best...
  11. Replies
    132
    Views
    76,426

    Ok Your right PaulStoffregen :) The Code is: ...

    Ok
    Your right PaulStoffregen :)
    The Code is:

    //Display
    #include <SoftwareSerial.h>

    // These are the Arduino pins required to create a software seiral
    // instance. We'll actually only use...
  12. Replies
    132
    Views
    76,426

    iam a not a programmer, what means this? ...

    iam a not a programmer,
    what means this?

    This report would have more information with
    "Show verbose output during compilation"
    enabled in File > Preferences.
    Arduino: 1.0.6 + Td: 1.20...
  13. i cleaned up and all the same. And what i don't...

    i cleaned up and all the same.
    And what i don't try until now :
    USB not connected, Push the button , holding the button and connecting the USB to the PC. hallelujah flashing led
    everything works...
  14. i use Windows 7 i found this ...

    i use Windows 7
    i found this
    http://forum.pjrc.com/threads/26065-Is-my-Teensy-3-1-dead?highlight=reset
    and i wil clean up, because i use some liquid for soldering and one time whit a arduino a...
  15. Teensy 3.1 no moor recognizing whit Win after all its working fine

    Hi
    i buy the Teensy3.1 and loaded up a program moor then 10 times (whit changes for step buy step make the program working for the project).
    now Windows dond recognizes the teensy .
    i try this...
Results 1 to 15 of 15