Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: Wibbing

Search: Search took 0.00 seconds.

  1. Ratiometric means: the output code is proprtional...

    Ratiometric means: the output code is proprtional to the RATIO BETWEEN THE INPUT VOLTAGE AND THE REFERENCE VOLTAGE.

    Example: If we use the ExcitationVoltage of a MeasuringBridge as reference and...
  2. For 3.6 I found with 3.3V ref FS will be 3V3 ...

    For 3.6 I found with 3.3V ref FS will be 3V3 and with 1.1V ref FS will be 1.1V .
    This is ratiometric. But i dont know about accuratie if you give him much less than 1V ref......
  3. I think, very_ high_speed and 16 bit resolution...

    I think, very_ high_speed and 16 bit resolution is not recomendet together.
    14 bit result is very good with buffer and filter and oversampling.

    I use startSycronisedReadSingle() with T3.6 for...
  4. Replies
    2
    Views
    81

    I will have the same problem. I tryed to use the...

    I will have the same problem.
    I tryed to use the internal tempSensor for regulating the temperatur on the chip, so i cold use the internal reference. But the use of the internal sensor doubles my...
  5. Replies
    10
    Views
    759

    I tryed to read the INTERNAL_TEMP_SENSOR ...

    I tryed to read the INTERNAL_TEMP_SENSOR

    Blocking mode analogRead () works.

    But non blocking not.

    I am still using T 3.6
  6. Pedvide did not answer last two years.

    Pedvide did not answer last two years.
  7. Replies
    7
    Views
    573

    Hi Paul, i want to use wire3, because the...

    Hi Paul,

    i want to use wire3, because the other wires use pins, witch are shared with functions i need.

    But i will commen out wire1 and wire 2.

    Thank You
    Lothar
  8. in ADC.cpp i found: #elif...

    in ADC.cpp i found:

    #elif defined(ADC_TEENSY_3_5) || defined(ADC_TEENSY_3_6)
    const uint8_t ADC::sc1a2channelADC0[]= { // new version, gives directly the pin number
    0, 68, 0, 64, 23, 14, 20,...
  9. i tried with ADC0 but sorry Paul, there is...

    i tried with ADC0 but

    sorry Paul, there is something missing i think:

    no matching function for call to 'ADC::startSynchronizedSingleRead(ADC_INTERNAL_SOURCE, const byte&)'


    it works with...
  10. merci merci

    merci merci
  11. Thank You. I think this is it. I will try it...

    Thank You.
    I think this is it.
    I will try it tomorrow.
    ( in Germany we have 11pm )
    Lothar
  12. adc->startSynchronizedSingleRead(pinLicht,ADC_INTERNAL _SOURCE::TEMP_SENSOR); -> Erro

    Hallo,

    i wanted mesure the chip Temperatur of my Teensy 3.6 and I found:


    adcErr = adc->startSynchronizedSingleRead(pinLicht,ADC_INTERNAL_SOURCE::TEMP_SENSOR); // produces Error :...
  13. I use 1 Dac as reference for 2 comparators and...

    I use 1 Dac as reference for 2 comparators and the second for one more. The 6bit DACs as reference did not work. The other DAC- inputpins are used for other functions or are not available on...
  14. Replies
    22
    Views
    8,837

    In the K66 Manual i found the single endet pins...

    In the K66 Manual i found the single endet pins of A10 and A11 are not the same as the differential pins and they are not in the teensy3.6 schematic. So i can not use them single endet?

    The names...
Results 1 to 14 of 14