Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: lsnyman

Search: Search took 0.00 seconds.

  1. Replies
    549
    Views
    277,762

    Ok More info. Connect Teensy LC - COM port 10...

    Ok More info.
    Connect Teensy LC - COM port 10 appears LED flashes 1Sec ON 1Sec OFF
    Press button on Teensy - LED stops flashing
    Upload Blink with new flash rate
    Nothing happens - Press button...
  2. Replies
    549
    Views
    277,762

    Thanks Paul. According to that info it is acting...

    Thanks Paul.
    According to that info it is acting normal as regards the button and LED, however it will not program. Loading the Blink Sketch on both the Teensy 3.1 and Teensy LC give the following...
  3. Replies
    549
    Views
    277,762

    As an update, Teensy LC shows up in device...

    As an update, Teensy LC shows up in device manager as Teensy USB Serial (COM10). If I press the reset button, it disappears and shows up under Human Interface Devices as USB Input Device. This is...
  4. Replies
    549
    Views
    277,762

    Used 2 different USB cables, also the Teensy 3.1...

    Used 2 different USB cables, also the Teensy 3.1 works without issues.
  5. Replies
    549
    Views
    277,762

    Tried both of those suggestions. No change....

    Tried both of those suggestions. No change.
    Pressing the button on LC causes the Serial port to disappear and also kills the flashing LED. Shorting PROGRAM to GND restores the flashing LED but still...
  6. Replies
    549
    Views
    277,762

    I am having an issue with this also. Firstly, my...

    I am having an issue with this also. Firstly, my Teensy 3.1 works fine, Uploading a sketch automatically reboots the board and all works well so I presume the Teensyloader is correctly configured,...
  7. Replies
    29
    Views
    11,771

    I am trying to use the sharp Memory LCD's and was...

    I am trying to use the sharp Memory LCD's and was looking for something that works to have a starting point. In this thread I saw Solardude's post
    I followed that link and downloaded the libraries,...
  8. Replies
    29
    Views
    11,771

    Hi Paul Here is the link...

    Hi Paul
    Here is the link https://code.google.com/p/arduino-sharp-memory-lcd-gfx-library/issues/detail?id=2
    It refers to the github link of the www.tindie.com library posted above by Solardude in...
  9. Replies
    29
    Views
    11,771

    I used the SharpMemoryLCD library referenced...

    I used the SharpMemoryLCD library referenced above on an Arduino UNO and got it to work with the Old Adafruit GFX library referenced on the Github page. I tried to use these with the Teensy 3.1 but...
  10. I made a bunch of breakout boards for the BL600 a...

    I made a bunch of breakout boards for the BL600 a while ago if anyone is interested. I have not had a chance to pursue the project but have the blank boards.
    See video...
  11. Replies
    8
    Views
    5,263

    Teensy 3.1 Diptrace Library

    If anyone is interested, I created DipTrace Schematic and Component libraries for Diptrace.
  12. Replies
    5
    Views
    2,333

    No problem, Thanks for the info. For a minute i...

    No problem, Thanks for the info. For a minute i thought no one here talked about I2C, SPI or FFT :)
  13. Replies
    13
    Views
    13,583

    Same problem with a MAX31855. Arduino code does...

    Same problem with a MAX31855. Arduino code does not work. Just returns 0's
  14. Replies
    5
    Views
    2,333

    Forum Search confusion

    Just a note, the search function on these forums don't seem to work properly unless i am doing something wrong. I have searched for a few subjects like I2C and SPI but found nothing so i just...
  15. Replies
    1
    Views
    2,414

    Very interesting. Good job

    Very interesting. Good job
Results 1 to 15 of 15