Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: bvernham

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    365

    Yep, Teensy 4.1 is my next stop. Problem is I...

    Yep, Teensy 4.1 is my next stop. Problem is I need to create a BOB with the necessary connections for peripheral like serial,display, I2C, general IO and the CAN transceivers,
  2. Replies
    16
    Views
    365

    No, I was responding to the post. The issue is...

    No, I was responding to the post.

    The issue is the only reason I need to use the downloaded installer vs the "APP" is because of TEENSY. No other boards have an issue with the APP from the APP...
  3. Replies
    16
    Views
    365

    This reason why I showed this is because I can...

    This reason why I showed this is because I can not compile anything. Due, Uno, Teensy, nothing.

    When I select Teensy 3.1/3.2 and try to compile I get the exact same message.
  4. Replies
    16
    Views
    365

    PS I can't compare any boards on the non APP...

    PS I can't compare any boards on the non APP version but I only need the non App version for Teensy boards.
  5. Replies
    16
    Views
    365

    How do you create a "portable folder"? Don't put...

    How do you create a "portable folder"? Don't put it in "program files"?
  6. Replies
    16
    Views
    365

    The latest one of the web site.

    The latest one of the web site.
  7. Replies
    16
    Views
    365

    Can't compile anything for my Teensies.

    I did a clean install of 1.8.13 on Windows 10 oro and I can not compile anything because is is looking for hardware/cores that no longer exist.

    Every time I try to compile anything I get: loading...
  8. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    I have reference for EKF implementation. The...

    I have reference for EKF implementation.

    The question I am asking is about this specific EKF implementation as the code is not really documented with comments and such.

    So anything that would...
  9. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    So the library expects the IMU input in the NED...

    So the library expects the IMU input in the NED convention?

    Also, is the any available paper/presentation/literature concerning the EKF in this library?

    I ask because I am very interest in...
  10. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    Update On Inverted ?

    Any update on why some of the IMU input are inverted within the update statement?

    Thanks

    Bruce
  11. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    Just wondering why the update statement has...

    Just wondering why the update statement has negation and swapping of axis for the accel and the gyro?

    ...
  12. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    My application will never have air speed as it...

    My application will never have air speed as it will be in a vehicle so some implementation like this is required:https://github.com/juangallostra/AltitudeEstimation

    But this would not fuse the GPS.
  13. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    Any plans on using the BME280 in the motion...

    Any plans on using the BME280 in the motion backpack for the INS or AHRS libraries? Typically baro, GPS, and vertical acceleration are fused to determined altitude.

    Thanks

    Bruce
  14. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    Can you provide a link/location of any material...

    Can you provide a link/location of any material which details the derivation of the 7 and 15 state EKF to which you have ported to GitHub?

    Thanks

    Bruce
  15. Thread: uNav INS

    by bvernham
    Replies
    709
    Views
    157,490

    Just found this code and it looks very...

    Just found this code and it looks very interesting. For my application, I need to have a remote antenna. I read in the thread that the PPS needs to be broken out. Besides the PPS signal is there...
  16. Replies
    2
    Views
    1,468

    Never mind! It helps when you read the...

    Never mind! It helps when you read the directions!
  17. Replies
    2
    Views
    1,468

    Teensy 3.6 Recognized By Arduino IDE 1.3.12

    I installed Arduino IDE 1.6.12 and Teensyduino 1.3.1 Beta2.

    I plugged the Teensy 3.6 in.

    The driver installs and it shows up as a in the device library as "Teensyduino RawHID".

    No port is...
  18. Replies
    359
    Views
    200,616

    I have searched the forum and have not seen a...

    I have searched the forum and have not seen a definitive answer if the FlexCAN library works with extended ID (29 bit) which is required for J1939.

    I can see the ID is defined as a unsigned 32 bit...
  19. Replies
    695
    Views
    450,488

    5444 Teensy at 100K with both SCL and SDA...

    5444

    Teensy at 100K with both SCL and SDA
    5445

    Teensy at 400K with both SCL and SDA

    100K will acknowledge but will not display demo sketch.

    Still just spinning my wheels here.
  20. Replies
    695
    Views
    450,488

    /* NKC Electronics serial display - Demo ...

    /*
    NKC Electronics serial display - Demo

    Demonstrates different functions of the Serial LCD module

    The circuit:
    * LCD SCL pin to Arduino SCL pin or Analog 5
    * LCD SDA pin to Arduino...
  21. Replies
    695
    Views
    450,488

    Cranky LCD

    I got home and got a hold of my scope. Please see below.
    5438



    5439

    Let me know if you have any ideas why this may be happening.
  22. Replies
    695
    Views
    450,488

    I have tried it on the Uno because fo the 3.3V vs...

    I have tried it on the Uno because fo the 3.3V vs 5V ratings. I need to check if this is 5V tolerant.

    I also tried lower 200K and 100K but still had the same problem.

    Thanks

    Bruce
  23. Replies
    695
    Views
    450,488

    "When you ran the LCD with the UNO, what did you...

    "When you ran the LCD with the UNO, what did you do for the 3v3 logic and power levels the LCD wants."

    My previous experience are using the 5V version of this LCD with the UNO/Mega/Mega Junior,...
  24. Replies
    695
    Views
    450,488

    I2C Slave LCD Not working

    I have and LCD I2C Slave:

    http://media.nkcelectronics.com/datasheet/NKC2004SD-NSW-BBW-33V33.pdf
  25. Replies
    695
    Views
    450,488

    Once again... both 10K and 5K (10K in parallel)...

    Once again... both 10K and 5K (10K in parallel) were tried with the same result.
  26. Replies
    695
    Views
    450,488

    Pull ups are 10K on the board. I tried adding...

    Pull ups are 10K on the board. I tried adding another 10K (so actually 5K) in parallel and it did not help.
  27. Replies
    695
    Views
    450,488

    I can't seem to get I2C to work correctly

    Arduino 1.0 library:


    /*
    NKC Electronics serial display - Demo

    Demonstrates different functions of the Serial LCD module

    The circuit:
    * LCD SCL pin to Arduino SCL pin or Analog 5
  28. Replies
    695
    Views
    450,488

    I2C LCD to working correctly

    I can't seem to get I2C to work correctly

    I tried the standard "wire.h" but I can not get the i2C LCD to work.

    I have used the Serial LCD Module 20x4 Blue with White Backlight 5v version for...
  29. Replies
    4
    Views
    1,129

    Can I get a hint? I see ICP1 and ICP3 but ICP3...

    Can I get a hint?

    I see ICP1 and ICP3 but ICP3 is also shared with the SPI buss so I want to specify the library to use ICP1.

    Is this possible?

    Thanks

    Bruce
  30. Replies
    4
    Views
    1,129

    Which input capture is used?: #define...

    Which input capture is used?:
    #define CAPTURE_USE_TIMER1
    #define CAPTURE_USE_TIMER2
    #define CAPTURE_USE_TIMER3

    1284P has 3 timers.

    Thank

    Bruce
  31. Replies
    4
    Views
    1,129

    FreqMeasure with 1284P

    I would like to use the FreqMeasure library with the 1284P but the library has not defined that microcontroller.

    Can someone help me modify so I can use that library with the 1284P?

    The...
Results 1 to 31 of 31