Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: ElkinDiaz

Search: Search took 0.00 seconds.

  1. Dear PJRC Community, I have find the issue it...

    Dear PJRC Community,

    I have find the issue it was a bad placement of one component in the assembly, please delete this thread.

    Thanks,
  2. Rigid-Flex Custom Teensy 3.2 not loading the firmware

    Dear PJRC Community,

    We have a prototype project that require a rigid flex PCB design. It implies a custom Teensy 3.2 board. We have already some experience with rigid Custom Teensy 3.2 with...
  3. Replies
    5
    Views
    384

    Dear Paul, I am using the 3.3V output from the...

    Dear Paul,

    I am using the 3.3V output from the Teensy to power other components that are using current, so it seems to explain my issue. I understand that I might improve the power line ciruict. ...
  4. Replies
    5
    Views
    384

    Dear PJRC Community, I have not received any...

    Dear PJRC Community,

    I have not received any reply, I understand that I might publish the complete source code, while I am not able to publish it, I have identified a part of the code that seems...
  5. Replies
    5
    Views
    384

    Teensy 4.0 randomly reset by itself

    Dear PJRC Community,

    I am trying to migrate Teensy 3.2 projects into the new Teensy 4.0, ideally using the same arduino firmware with compatible libraries should be compatible, and the performance...
  6. Thanks luni! I will use your library.

    Thanks luni!

    I will use your library.
  7. DSE and SRE configurations

    Thanks for the fast reply, I want to be able to enable or disable this options for the GPIO, so as I could understand, if I want to modify this I can directly modify the CORE_PIN#_CONFIG register...
  8. Teensy 3.6 pinMode and DSE and SRE configuration for GPIOs

    Dear PJRC community,

    We have a project based on the Teensy 3.6, we would need to modify or configure the Drive Strength Enable DSE and the Slew Rate Enable SRE options for a particular GPIO. As...
  9. Replies
    56
    Views
    40,656

    Procedure to Change Name of Teensy 3.2

    Dear Teensy comunity,

    I would like to change the name of the device, I am using it in the USB Type: "Serial". When I upload the firmware into a Teensy 3.2, I get the device name: "USB Serial".
    ...
  10. Replies
    5
    Views
    1,962

    I wrote my own functions to read and it worked,...

    I wrote my own functions to read and it worked, so I did not need to use the HDC library and it works perfect.

    Thanks for the support.
  11. Replies
    5
    Views
    1,962

    Thanks for the ideas, Paul I am trying to use...

    Thanks for the ideas,

    Paul I am trying to use the ClosedCube HDC1080, I need to connect it to the i2c Wire1 interface on pins 29 and 30. ...
  12. Replies
    5
    Views
    1,962

    Arduino HDC1080 Library compatibility

    Dear Teensy Community,

    I would like to use a humidity&temperature sensor which is controlled or acquired by i2c bus. I am trying to use the Arduino library in order to access to the sensor data. ...
  13. Teensy UART (Hardware Serial) and I2C problem

    Hello Everyone,

    I am trying to communicate serially with the PC at 460800 bauds, in order to do it, I am connecting a FTDI circuit, and I am using the flow control signals CTS and RTS. I'm able...
  14. Replies
    8
    Views
    1,497

    Hi Paul, I had a problem with my external...

    Hi Paul,

    I had a problem with my external source, it was giving a little overvoltage at start, I changed it and now it works.

    Thanks for your fast support.

    Regards.
  15. Replies
    8
    Views
    1,497

    The Teensy runs the code, and it looks that it...

    The Teensy runs the code, and it looks that it retain the code, because I am using the simple /* LED Blink, Teensyduino Tutorial #1, however when I restart it, I found that the only way to see the...
  16. Replies
    8
    Views
    1,497

    Hi Paul, In the Teensy 3.x schematics I find...

    Hi Paul,

    In the Teensy 3.x schematics I find there are two nets named as VBAT, the external pin VBAT, and also the internal pin 21 of the Kinetis called VBAT. I have disconnected the external pin...
  17. Replies
    8
    Views
    1,497

    Thanks for the reply WMXZ, I attach here the...

    Thanks for the reply WMXZ,

    I attach here the schematics.

    9657

    I found strange that the Teensy loads well the arduino sketch, but when I restart it, is missing anything, and only start...
  18. Replies
    8
    Views
    1,497

    Custom Teensy starting up problem

    Hi PJRC Team,

    First of all I would like to mention that I find the Teensy project a very competitive solution for develop arduino projects. I have used teensy 3.2 for many projects, and I found a...
Results 1 to 18 of 18