Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: KenHahn

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    90

    That example doesn't completely initialize the...

    That example doesn't completely initialize the Ethernet. This link may help get you started on the right track. https://forum.pjrc.com/threads/68083-Teensy-4-1-Ethernet-link-status-won-t-connect
  2. Replies
    3
    Views
    94

    Here is the code, though it is pretty much the...

    Here is the code, though it is pretty much the stock example code minus some misc stuff that wasn't being used in my particular application. I started to pull stuff out after running into the issue...
  3. Replies
    3
    Views
    94

    Uncanny Eyes and Audio Adapter Issues

    I decided to do a Halloween project (Zombie Operation Game) using Uncanny Eyes coupled with the Audio adapter to play various sound effects.

    I am using Teensy 4.1 with the Rev D audio adapter. ...
  4. If I am understanding your setup correctly, it...

    If I am understanding your setup correctly, it sounds like the I2C is connected via an external cable as shown in your pic so the I2C not coming from the Teensy but rather an external device?

    If...
  5. Replies
    6
    Views
    417

    You want to cut the small trace that is between...

    You want to cut the small trace that is between the two large pads to isolate the USB power from the VIN power.

    Use a sharp X-acto or box knife with a new blade. Angle the blade at about a 45...
  6. Replies
    6
    Views
    417

    Under normal circumstances, the CPU should not be...

    Under normal circumstances, the CPU should not be getting that hot. It would normally just be warm to the touch.

    If you are plugging both USB and VIN power in at the same time, besides the diode...
  7. Replies
    11
    Views
    1,317

    As Defragster has pointed out, I have some of the...

    As Defragster has pointed out, I have some of the Teensy 4.1 in stock, though I am a little surprised he can see my website at all. ;)

    Most of the ones I sell are the value-added 'Fully Loaded...
  8. Replies
    2
    Views
    129

    It is the 4th pin down. It goes GND, 0, 1, 2

    It is the 4th pin down. It goes GND, 0, 1, 2
  9. Replies
    2
    Views
    232

    There is a small trace connecting those pads...

    There is a small trace connecting those pads which can be hard to see and that is what you want to cut to separate VIN and VUSB power.

    28109
  10. Replies
    5
    Views
    473

    Communicating over a serial port doesn't mean you...

    Communicating over a serial port doesn't mean you need to use AT commands with the ESP32. You can write whatever program you want to run on the ESP32 and use the serial port to pass information back...
  11. Replies
    5
    Views
    558

    The LED effect you are seeing is because the...

    The LED effect you are seeing is because the active inputs to the unpowered chip are leaking current through the chips input protection diodes and thus putting a little voltage/current on the power...
  12. Replies
    7
    Views
    463

    You might want to verify that the OE pin on the...

    You might want to verify that the OE pin on the TXS0108E is pulled high to enable the part. Looks like it could be reading floating bits.
  13. You can use the same SPI bus for both. As...

    You can use the same SPI bus for both. As Defragster mentioned, only the CS needs to be unique between them so they don't conflict when they share the same bus.


    Correct


    Correct. You don't...
  14. Replies
    10
    Views
    1,058

    Your scheme would work if you can find the pins,...

    Your scheme would work if you can find the pins, though I think the soldering might be difficult. Something like these pins with removeable carrier if found in shorter length or trimmed to length...
  15. Don't know if you are still messing with this,...

    Don't know if you are still messing with this, but it looks like your R- pin solder did not flow correctly.

    25753
  16. That trace just feeds 3.3V to the optional 25K...

    That trace just feeds 3.3V to the optional 25K potentiometer. Since it appears you are not using that part, cutting the trace won't affect your setup. If it is a solder bridge, you should also be...
  17. Probably a long-shot, but take a closer look at...

    Probably a long-shot, but take a closer look at the area I have circled in red. That small trace running between the GND pin and Pin 0 is connected to 3.3V. Perhaps the solder resist is getting...
  18. Replies
    2
    Views
    529

    The MOSFET SP8M21FRA seems like it should work OK...

    The MOSFET SP8M21FRA seems like it should work OK at 3.3V. If you have 5V available and drive it with something like a 74HCT125 between the Teensy and the MOSFET, it will help to ensure Rds(on) is...
  19. Your symptoms sound like a thermal issue to me. ...

    Your symptoms sound like a thermal issue to me. The only real difference between a short power cycle which doesn't fix the issue and a long one which does, is that the components have time to cool...
  20. I think he saw that it is flagged as not...

    I think he saw that it is flagged as not recommended for new designs which is different than going EOL.
  21. Replies
    28
    Views
    2,541

    mjs513, the datasheet I linked to from LCSC site...

    mjs513, the datasheet I linked to from LCSC site is Rev 0.7 and shows 144MHz max data rate. There is an older datasheet I have come across that showed 100MHz, so I think they updated it at some...
  22. Replies
    28
    Views
    2,541

    I'd be happy to send some to Paul if he would...

    I'd be happy to send some to Paul if he would like to test them himself and add them to his approved alternate list. Not sure if there is a more strenuous test than the standard memtest that can be...
  23. Replies
    28
    Views
    2,541

    Another PSRAM option - Lyontek LY68L6400S

    I have seen the LY68L6400S mentioned before, but found no confirmation if they were in fact a valid alternate so I brought some in to test since chip shortages are going to be around for awhile.
    ...
  24. Replies
    15
    Views
    2,274

    I had the parts to duplicate your basic setup...

    I had the parts to duplicate your basic setup with the LCD on Port1. It worked as expected, so I suspect there must be a wiring issue somewhere as others have mentioned.

    25036
    25037

    --- Ken
  25. Replies
    15
    Views
    2,274

    I can confirm that the I2C to parallel adapter...

    I can confirm that the I2C to parallel adapter boards on the back of these LCDs do include pull-ups on the SDA and SCL lines.
  26. I might be able to help you out. I sell the...

    I might be able to help you out. I sell the Teensy 4.1 as a fully populated board including the extra PSRAM and Flash memory chips, Ethernet header and pins.

    I thought about also adding a...
  27. Replies
    174
    Views
    41,668

    I'm with KurtE on this. 1. Go after the very...

    I'm with KurtE on this.

    1. Go after the very low hanging fruit first like cleaning up the navigation in the menus and adding links on product pages to make it easier to find the other info that...
  28. Replies
    28
    Views
    7,463

    As BriComp already mentioned, I'm not currently...

    As BriComp already mentioned, I'm not currently setup to ship internationally but I have customers in Europe and the Middle East that use freight forwarding services and those seem to work fairly...
  29. Replies
    28
    Views
    7,463

    Thanks for the order. 64MB Flash and shorty...

    Thanks for the order. 64MB Flash and shorty headers as well as the taller Ethernet headers Paul pointed to are inbound.

    If you'd like I can hold the order until the chips come in so you don't...
  30. Replies
    28
    Views
    7,463

    I'll go ahead and source some of the W25Q512JVEIQ...

    I'll go ahead and source some of the W25Q512JVEIQ to have on-hand by next week in case anyone needs them. Will also get the shorty headers inbound.

    Good idea on the memory layout, I will add that...
  31. Replies
    28
    Views
    7,463

    That is the line I was looking at. I think they...

    That is the line I was looking at. I think they are the way to go because you can easily cut the female connectors. They are also a little shorter than the normal shorty headers. I currently sell...
  32. Replies
    28
    Views
    7,463

    Good idea on the low profile headers. Also will...

    Good idea on the low profile headers. Also will look at sourcing short male headers to go with.

    The Mega 2560 Pro MCU board is designed specifically for the Mega 2560 Pro module and only works...
  33. Replies
    28
    Views
    7,463

    Thanks Phil, your order will go out Monday. ...

    Thanks Phil, your order will go out Monday.

    Funny you mentioned the Blue Pill. I have a stack sitting here on my desk. I was going to productize them and offer them assembled with the Arduino...
  34. Replies
    28
    Views
    7,463

    My premise is that Teensy should really be more...

    My premise is that Teensy should really be more pervasive in the mainstream hobby than it is. Putting the most power in the smallest package provides great performance but also tends to create some...
  35. Replies
    28
    Views
    7,463

    New Supplier for Teensy - ProtoSupplies.com

    Hi everyone

    My name is Ken Hahn, and I would like to introduce myself and my company ProtoSupplies.com as another option for buying Teensy products and related accessories. We are an official...
Results 1 to 35 of 35