Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: smarrocco

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    435

    [queued] Custom Keypad with Teensy

    I finally completed my first Teensy project. It's a custom keypad in a vertical format for use with graphics software alongside a Wacom tablet. It uses a Teensy 4, a micro SD Card and 3.75" TFT LCD...
  2. Replies
    6
    Views
    536

    Thank you. The Protocol Buffers material look...

    Thank you. The Protocol Buffers material look interesting also, but the simplicity of the serial option might be just what I need for this project.
  3. Replies
    6
    Views
    536

    Thanks jdriedger. I was unaware that I could...

    Thanks jdriedger. I was unaware that I could communicate with serial over the same USB being used for other things. That does look like the simplest method.
  4. Replies
    6
    Views
    536

    Sending data into Teensy 4

    I have a Teensy 4 running an application that has some settings that are read at startup. The C++ code contains those setting in the source. I would like to be able to modify the settings without...
  5. Replies
    7
    Views
    334

    I've brushed away as much as possible to narrow...

    I've brushed away as much as possible to narrow down this issue. At first glance, it seems very similar to a posting someone else made on the forums regarding Blinkie code "fixing the problem", but I...
  6. Replies
    7
    Views
    334

    Yes, only one Teensy 4 is connected. Wiring is...

    Yes, only one Teensy 4 is connected. Wiring is unchanged, lengths, cables, hardware setup. It was working fine, then after one compile this message began appearing. Sometimes (maybe one in 10 times)...
  7. Replies
    7
    Views
    334

    "error sending reboot command (HID)"

    I've begun seeing this error command ("error sending reboot command (HID)") when upload to a teensy 4. It happens approximately 90 times out of 100, with the other ten occasions working successfully....
  8. Suggested solutions have resolved the issue... ...

    Suggested solutions have resolved the issue...

    @defragster--Windows 10 OS, Teensy Loader 1.49.

    I can confirm some of the timing issues you mentioned--Drilling into some of the keyboard...
  9. USB Type: Keyboards vs. Serial? What does it do?

    I've been having some difficulties with getting a compile to succeed for a Teensy 4 when my code utilizes the Keyboard library.

    The code only successfully compiles (when it includes the command...
  10. strange issue with "'Keyboard' was not declared in this scope" error.

    A minimal Teensy 4 Sketch in the Arduino IDE consisting of using the function:

    Keyboard.Print("Hello");

    ...yields an error message of
    "....Multiple libraries were found for "Keyboard.h"...."...
  11. Replies
    6
    Views
    323

    [QUOTE=KurtE;226861]In cases like this, it would...

    [QUOTE=KurtE;226861]In cases like this, it would be good if you could give a link to the display that you are using...


    Good point, KurtE: The display I am using is this...
  12. Replies
    6
    Views
    323

    Gibbedy: According to the LCD docs, it should be...

    Gibbedy:
    According to the LCD docs, it should be fine with a supply from 3-5volts so I expect is would not be because the teensy 4 is 3.3v.

    defragster,
    I am not certain of the expected current...
  13. Replies
    6
    Views
    323

    Gibbedy: According to the LCD docs, it should be...

    Gibbedy:
    According to the LCD docs, it should be fine with a supply from 3-5volts so I expect is would not be because the teensy 4 is 3.3v.

    defragster,
    I am not certain of the expected current...
  14. Time delay betwene pin_mode() changes necessary?

    I've been playing with a small matrix keypad with diodes and the Teensy 4 and keypad library. A small test application I wrote that works fine on an Arduino Pro Micro was behaving differently on the...
  15. Replies
    6
    Views
    323

    Issue using PWM output on Teensy 4

    I am attempting to control the brightness (via the LITE pin) on a 3.5" LCD TFT (HX8357 based) display with a PWM output from a Teensy 4. Previously, I was able to do this on a SparkFun Pro Micro...
  16. [QUOTE=PaulStoffregen;226088]After you've pressed...

    [QUOTE=PaulStoffregen;226088]After you've pressed the button, does the red LED stay on solid, or blink slowly?



    The red LED stays on steady.

    As you suggested, I tried another cable. That...
  17. Having problems getting started with Teensy 4.0 and Arduino IDE...

    I have done a fresh install of the Arduino 1.8.10 IDE, followed by an install of the TeensyduinoInstall.exe 1.48.

    I am using a basic sketch that compiles with no issues.
    Arduino menu:
    Board is...
Results 1 to 17 of 17