Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: WMXZ

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Audio to UDP

    by WMXZ
    Replies
    5
    Views
    339

    In addition to AudioInputUSB you need a 'real'...

    In addition to AudioInputUSB you need a 'real' input or output object, e.g. AudioInputI2S (simply declare object without any connections). Reason: USB is not triggering the audio processing
  2. I simply added a new wav header chunk to extend...

    I simply added a new wav header chunk to extend the wav header from 44 to 512 bytes. This chunk could hold also additional meta data. only problem could be that added chunk must be properly...
  3. HalfKey bootloader cannot be overwritten! It is...

    HalfKey bootloader cannot be overwritten! It is in a separate chip.
  4. I would start with...

    I would start with https://github.com/libusb/hidapi
    and first try to get a standalone program working and then generate a mex file
  5. Replies
    11
    Views
    302

    As side note: I frequently use Putty to open a...

    As side note: I frequently use Putty to open a terminal to Teeny while programming with VisualCode (Win10) using VisualTeensy task macros. In order to download from VC, I have to first close Putty,...
  6. Replies
    15
    Views
    462

    That's why I stick to additional audio boards....

    That's why I stick to additional audio boards. Also as my applications is very special (8-chan data logger, 96-192 kHz, 18-20 bit, ADC only: I use 2 TI TLV320ADC5150)
  7. Replies
    15
    Views
    462

    While I agree with Paul's comment...

    While I agree with Paul's comment https://forum.pjrc.com/threads/40403-Difference-between-other-audio-board?p=125796&viewfull=1#post125796 on this issue,
    there are applications that would benefit...
  8. Replies
    15
    Views
    462

    the SGTL5000, really? maybe a much higher...

    the SGTL5000, really?
    maybe a much higher quality chip would make sense.
    I prefer as it is now with audio an add-on, so everyone can choose.
  9. as I2S uses PIN13 for data input, you mast use...

    as I2S uses PIN13 for data input, you mast use Pin14 as alternate SPI_CLK (Assume you are using T3.x)
  10. Replies
    14
    Views
    299

    Hove a look into the src code and you will see it...

    Hove a look into the src code and you will see it Serial.begin(...) does nothing.
    it is not needed, but you can keep it for compatibility.
    BTW, speed is always USB max speed
    Different for HW...
  11. Replies
    11
    Views
    302

    deinstall the wrong comport and then reattach T3.6

    deinstall the wrong comport and then reattach T3.6
  12. Replies
    42
    Views
    1,159

    I have a PR pending on adding a function to...

    I have a PR pending on adding a function to DMAChannel.h to allow ISR to be executed at specific interrupt level.
  13. Replies
    29
    Views
    1,161

    But keep in mind, in the end all become machine...

    But keep in mind, in the end all become machine language, even when interpreting p-code.
    So it depend a lot of your skills and mindset, right?
    So I would say, choose the tool that is right for the...
  14. So, you are using https://github.com/yoonghm/MTP,...

    So, you are using https://github.com/yoonghm/MTP, right?
    I cannot comment on this, but typically with SdFAT there is a potential conflict with SD (in Teensyduino) both have the same include file...
  15. Did you try to use one of the examples and what...

    Did you try to use one of the examples and what exactly is your problem.
    Did you read and follow the readme and what did not work?
    Finally, what Library do you wanted to use? (give us a link)....
  16. Thread: Teensy MicroMod

    by WMXZ
    Replies
    25
    Views
    795

    would be interesting to see if flexibility of...

    would be interesting to see if flexibility of T4.1 (multiple I2S data ports, PSRAM could be mapped to Sparkfun form factor)
    I guess, I stick with T4.1 for some time.

    EDIT: OK I may change my...
  17. Replies
    57
    Views
    2,145

    on https://www.pjrc.com/store/teensy41.html in...

    on https://www.pjrc.com/store/teensy41.html

    in
    "Teensy 4.0 can be programmed using the Arduino IDE with Teensyduino add-on."
    change 4.0 to 4.1
  18. See other thread on MTP responder!

    See other thread on MTP responder!
  19. Replies
    1
    Views
    129

    see other thread on MTP responder. It was first...

    see other thread on MTP responder. It was first ported to T3.x.
  20. but where is the algorithm?

    but where is the algorithm?
  21. Replies
    5
    Views
    338

    Is that not what one would expect? All data are...

    Is that not what one would expect?
    All data are store in binary form, this is also valid for the mantissa. I guess that 223.98 cannot be expressed in binary form (binary exponent and mantissa).
    I...
  22. Replies
    21
    Views
    576

    There are special considerations concerning...

    There are special considerations concerning ground and connections for Xtal. There were discussed here in the forum. A search may find them.
  23. Replies
    21
    Views
    576

    Yes, they are in the chip and can be changed by...

    Yes, they are in the chip and can be changed by software. Years ago, FrankB made a sketch that played "FM music" by changing theses capacitors.
  24. Great to hear that. Sure, 'debugging' code is...

    Great to hear that.
    Sure, 'debugging' code is only that. it was done to give some feedback to user. It was not meant to be detection logging. Yous could be very useful indeed, but max be very...
  25. Replies
    4
    Views
    209

    old audio shield does NOT work on Teensy 4, when...

    old audio shield does NOT work on Teensy 4, when soldered pin to pin.
    you need Audio board Version D for pin to pin compatibility with teensy 4.x
  26. Replies
    21
    Views
    576

    The ferrite chip is indeed indicated as 120 Ohm...

    The ferrite chip is indeed indicated as 120 Ohm impedance (most likely at 100 Mhz as in most cases)
  27. Yes, for the time being, there are #if MDEL

    Yes, for the time being, there are #if MDEL<0 ....#endif around the calls to checkDutyCycle()
    But this is only to see if event-driven recording is working as expected.
    On the bench here it was...
  28. I cleaned up the code to get event driven logger...

    I cleaned up the code to get event driven logger working

    It turned out that the code in #179 could work:
    In order to allow pre-trigger delay the trigger process has to run in parallel.
    However,...
  29. An update I'm working on it There seems nothing...

    An update
    I'm working on it
    There seems nothing wrong with detector in mProcess.h (even if I'm modifying it a little bit)
    BUT I found this

    #include "mProcess.h"
    mProcess...
  30. Thread: audio clock slip

    by WMXZ
    Replies
    15
    Views
    457

    I'm not sure if this datasheet describes recent...

    I'm not sure if this datasheet describes recent model, but be aware that they had a design flaw such that they lost vacuum when stored over 30 dec C.
    I only can see an advantage if Teensy can run...
  31. I guess, I have to setup the hardware to test...

    I guess, I have to setup the hardware to test further
    can you confirm T3.6 and 2 I2S micros?
  32. It is intended that program continuously checks...

    It is intended that program continuously checks if should close a file or hibernate. This is to allow files that are opened and closed on the second, and to have duty cycles that are on nice numbers....
  33. Replies
    4
    Views
    165

    SD library from TD does not support exFAT. For...

    SD library from TD does not support exFAT.
    For ExFAT you need SdFAT-beta from Bill (AFAIK)
    In case you install SdFAT-beta, best you delete the SD library due to conflicting include filers.
  34. Replies
    4
    Views
    165

    Did You try the examples provided with the...

    Did You try the examples provided with the libraries?
    Anway chipSelect must be BUILTIN_SDCARD for T3.6 (not SS)
  35. there is nothing magic have a look into...

    there is nothing magic
    have a look into pins_teensy.c in cores (I checked with teensy3)
  36. I still need to spin-up my memories. the snippet...

    I still need to spin-up my memories.
    the snippet detection mode was not really tested widely.

    But, what I would try is two things.
    -make sure that mustClose=0; in config file
    - snipParameters =...
  37. I will have a look into this

    I will have a look into this
  38. Changing the parameters required some design...

    Changing the parameters required some design decision.
    For rebooting from hibernate, parameters need to be read from permanent storage. It was decided from disk.

    This is valid also for start...
  39. The TimeLib warning, is only a gentle reminder to...

    The TimeLib warning, is only a gentle reminder to not to use Time.h if you wanted to include the Arduino TimeLib library. (have a look into TimeLib/Time.h)
    It seems that TimeLib was written by a...
  40. SdFat is a replacement of SD, so you should not...

    SdFat is a replacement of SD, so you should not include both, also it may be necessary to remove SD from library, as it also has a SdFat.h which may results in missing references.
  41. writing your own lib is easy: So take, say I2S...

    writing your own lib is easy:
    So take, say I2S input interface, you will see that there are two parts, one that is configuring the I2S interface, the other is a DMA.
    Now, you have two options:...
  42. At this point you must check if the RPi is...

    At this point you must check if the RPi is providing proper I2S data stream (64 data bits / frame-sync) I cannot tell you how you can get this info apart from using a oscilloscope or logic analyser....
  43. I have not worked with this for a while, but it...

    I have not worked with this for a while, but it seems that the different mods done since beginning generated some incompatibilities.
    In particular, the #defines are corrupting the templates, I was...
  44. any picture of your cut?

    any picture of your cut?
  45. Replies
    17
    Views
    626

    here is the link...

    here is the link https://www.pjrc.com/teensy/td_download.html

    Teensy.exe is only the downloader program that indeed says 1.52, but the whole system including toolchain is on td_download page....
  46. Replies
    4
    Views
    202

    I appreciate the risk and routing. But if the two...

    I appreciate the risk and routing. But if the two pads were small ovals (or rectangles) twice the size of the actual dots, soldering would be easier, safer?
    Anyhow, I succeeded to solder two short...
  47. Replies
    2
    Views
    173

    T3.2 does not have SDIO, you must use SPI

    T3.2 does not have SDIO, you must use SPI
  48. Replies
    4
    Views
    202

    I know, the sequence of 5 USB pins on the side...

    I know, the sequence of 5 USB pins on the side are for 2nd USB that one typically uses for USH-Host, but can be programmed as USB device.
    But if you, like me, wanted to use USB not only for Serial...
  49. Replies
    17
    Views
    626

    latest TD is 1.53 (on all platforms)

    latest TD is 1.53 (on all platforms)
  50. OK, frank the RFFT really calls a N/2 complex...

    OK, frank
    the RFFT really calls a N/2 complex FFT (generating N/2 frequencies), to go back to real time series you take the N/2 frequencies, after manipulation, and come back to N real numbers.
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4