Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: PaulStoffregen

Page 1 of 10 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    4
    Views
    113

    Teensy can communicate MIDI in 3 different ways....

    Teensy can communicate MIDI in 3 different ways.

    1: Serial MIDI, which uses 5 pin DIN connectors.

    2: USB device MIDI, where Teensy communicates MIDI with your PC in the manner a USB MIDI...
  2. Replies
    3
    Views
    65

    Most Arduino libraries work. Libraries...

    Most Arduino libraries work.

    Libraries designed to work on any board usually run fine.

    Many of the libraries are for sensors which use I2C or SPI communication. They generally work, because...
  3. Very unusual for either of those 2 parts to get...

    Very unusual for either of those 2 parts to get hot.

    Usually when things go wrong, the PTC fuse (small white part near the USB connector and 3V pin) gets hot. The voltage regulator (6 pin part...
  4. Sadly, even the charge-only cables look like...

    Sadly, even the charge-only cables look like regular USB cables. Some even have the USB logo, infringing the USBIF trademark rules.
  5. I realize you've said your USB cable is good. ...

    I realize you've said your USB cable is good. I'm guessing you're probably not wanting to hear this, but I really do need to say we've heard this sort of problem over and over. It's almost always a...
  6. Just to confirm, is the orange LED blinking each...

    Just to confirm, is the orange LED blinking each time you power up the board? Orange blinking confirms the original program loaded during testing is still present and the Teensy is managing to boot...
  7. This really should work, since that attribute...

    This really should work, since that attribute walk has these lines:



    ATTRS{idVendor}=="16c0"

    ATTRS{idProduct}=="04d0"

    I tested it just now on Ubuntu 18.04. It's definitely...
  8. I'm not even sure I know what "this" really is. ...

    I'm not even sure I know what "this" really is. Any chance you can show us the code you're trying and give some more specific detail about these pulses (maybe a oscilloscope screenshot)?
  9. Try adding delay(50); after Serial3.begin(), so...

    Try adding delay(50); after Serial3.begin(), so the transmit pin is idle for a while before you send anything.

    Or try connecting a 10K resistor between TX3 and 3.3V, so the transmit pin is at the...
  10. snprintf() works, perhaps awkwardly if you like...

    snprintf() works, perhaps awkwardly if you like C++, but it's highly reliable ;)



    void setup() {
    while (!Serial);
    double x = 1.000000123L;
    char buf[24];
    snprintf(buf, 24, "%.9lf",...
  11. Please run "udevadm info --attribute-walk...

    Please run "udevadm info --attribute-walk /dev/hidraw3" and copy the lengthy output here, so we can see what's really going on.
  12. Replies
    23
    Views
    783

    Can Discourse import our existing vBulletin data?

    Can Discourse import our existing vBulletin data?
  13. Arduino String and Serial.println only support 32...

    Arduino String and Serial.println only support 32 bit floats.

    To print 64 bit double, use Serial.printf(). To convert to a string, use snprintf().



    void setup() {
    Serial.begin(9600);
    }
  14. Yes, looks like the C library is defining y0(),...

    Yes, looks like the C library is defining y0(), y1(), yn(), j0() and other functions with global scope.

    https://www.gnu.org/software/libc/manual/html_node/Special-Functions.html

    These names can...
  15. Replies
    8
    Views
    159

    Many people have reported both of these parts to...

    Many people have reported both of these parts to work.
  16. Maybe first re-heat the 8 solder connections? ...

    Maybe first re-heat the 8 solder connections? Apply liquid flux, if you have any. Don't be shy about leaving your soldering iron in contact for several seconds, since you can't make the chip any...
  17. That's the purpose of volatile. It forces code...

    That's the purpose of volatile. It forces code to actually read the variable, so you *can* change it in the ISR and have your program detect the change.

    Without volatile the compiler makes a lot...
  18. Cortex-M7 has a 32K data cache. To properly test...

    Cortex-M7 has a 32K data cache. To properly test the PSRAM, you need to flush and delete the cached data with arm_dcache_flush_delete(address, size). See the memory test program for an example.
    ...
  19. Microsoft loves their Windows Registry, so much...

    Microsoft loves their Windows Registry, so much that they cache USB device detection into and pull it from the registry and use that cached info, even when it's just been freshly read from the USB...
  20. Replies
    4
    Views
    219

    The test fixtures we use for testing each Teensy...

    The test fixtures we use for testing each Teensy do this by driving all (or almost all) the pins with a shift register. Resistors are used between the shift register outputs and Teensy pins. Some...
  21. Agreed, you need to solder the connections to the...

    Agreed, you need to solder the connections to the switches.

    I still recommend running File > Examples > Teensy > USB_Keyboard > Buttons simply to test the hardware using known-good software.
    ...
  22. Yes, absolutely, we see this sort of thing all...

    Yes, absolutely, we see this sort of thing all the time. It can be very difficult to know whether a problem is caused by hardware or software when you're creating both.

    One way to troubleshoot...
  23. Replies
    22
    Views
    375

    Any chance you could explain how to run this...

    Any chance you could explain how to run this test?

    What are those plots? Are they from a logic analyzer or USB oscilloscope? Is that the voltage on pin 13? Or are you collecting data somehow...
  24. If that hardware is still connected, remove...

    If that hardware is still connected, remove everything from the Teensy 3.6 except the USB cable.

    If it's still not responding, try measuring the voltage at VIN (which should be approx 5V if USB...
  25. This library is using the FTM1 timer. For...

    This library is using the FTM1 timer. For documentation on FTM1 on Teensy 3.2, you need the MK20DX256 manual. Get it here:

    https://www.pjrc.com/teensy/datasheets.html

    The 2 registers which...
  26. Replies
    4
    Views
    401

    Yes, I will admit, my concern about bottom side...

    Yes, I will admit, my concern about bottom side pads & signal integrity was overly conservative. Several other decisions that went into Teensy 4.0 could probably also, in hindsight, be considered on...
  27. Usually these sorts of strange noise problems are...

    Usually these sorts of strange noise problems are a "ground loop". Usually there is another connection, like to an amplifier, where some of the power supply current unintentionally flows through...
  28. Replies
    4
    Views
    156

    Maybe the wires aren't connected properly? Or...

    Maybe the wires aren't connected properly? Or maybe there's a mistake somewhere in your program? All it would take is one "Serial4" not changed to "Serial7", sort of like how your message has...
  29. Yes. With the audio library you can generate...

    Yes. With the audio library you can generate many different sounds and combine them with mixers.

    To see how, check out this 31 page tutorial on the audio library.
    ...
  30. Maybe this? ...

    Maybe this?

    https://www.digikey.com/product-detail/en/mill-max-manufacturing-corp/350-10-114-00-006000/ED6864-14-ND

    or this?
    ...
  31. Replies
    3
    Views
    149

    Bill's SdFat library might be able to give you...

    Bill's SdFat library might be able to give you the required sequential write speed. But it's quite a bit more complicated to use than the normal SD lib.

    As for external RAM size, today 8MB chips...
  32. Well, at least it didn't take a lot of work to...

    Well, at least it didn't take a lot of work to try it. When I added -felide-constructors many years ago (around Arduino 0019, when String was added), there were a couple cases where...
  33. I'm afraid the only solution might be the...

    I'm afraid the only solution might be the difficult task of trimming your code.

    But one easy thing you might try is editing boards.txt. Look for this line:

    ...
  34. To quickly answer your questions... The...

    To quickly answer your questions...




    The array index is independent of the type of array's actual data. You can have an array of float or an array of a struct. Regarding the index, the...
  35. Thanks. I've put this on my high priority issue...

    Thanks. I've put this on my high priority issue list. Hope to look into it this weekend.
  36. Replies
    19
    Views
    401

    While the language in this image is a bit strong,...

    While the language in this image is a bit strong, as someone who lives in the outskirts of the greater Portland area and personally knows some of the protesters, I can confirm it really does...
  37. Wow, maybe this is a previously unknown & elusive...

    Wow, maybe this is a previously unknown & elusive bug?!

    Can I talk you into sharing the compiled .elf and .hex files for both the Teensy 4.0 and Teensy 3.6? That will let me try it here on Ubuntu...
  38. Another guess... maybe the software analysis is...

    Another guess... maybe the software analysis is configured incorrectly. Maybe it's looking at the data waveform during the falling edge rather than at the rising edge?

    Together with (assuming)...
  39. I tried running your code here on a Teensy 4.1. ...

    I tried running your code here on a Teensy 4.1. Here's what my scope sees:

    21189

    The 82 80 result is very consistent.

    Admittedly, I connected this quickly on a breadboard with a few inches...
  40. What equipment are you using to make these...

    What equipment are you using to make these measurements? Those images look more like a logic analyzer than any oscilloscope I've ever seen!

    I loaded your first image into an editor, so I could...
  41. In the short term, I'm aiming for a much lower...

    In the short term, I'm aiming for a much lower goal... just to make the File class from SD into a base class which can be shared among libraries.

    Years ago I started a redesign of the SD library. ...
  42. Replies
    2
    Views
    134

    Teensy 4.1 has plenty of PWM pins, so you can...

    Teensy 4.1 has plenty of PWM pins, so you can probably just use 8 of those. Just use analogWrite(pin, value) to control them, perhaps with something like elapsedMillis in loop() or IntervalTimer to...
  43. RS485 does sound like a pretty good approach. If...

    RS485 does sound like a pretty good approach. If using the CAT5 cables, you might have one pair for bidirectional data and perhaps dedicate a pair for a simple unidirection pulse from the server to...
  44. My general feeling about whitespace (expect...

    My general feeling about whitespace (expect Python) is usually to leave well enough alone, especially if the code has already been widely shared.

    Personally I try to keep everything within a 100...
  45. Replies
    23
    Views
    783

    I'm been debating whether to keep private...

    I'm been debating whether to keep private messages enabled. Looking for feedback on this. Please share your thoughts. Is PM valuable?

    The main problem with PMs is spam. With normal public...
  46. Replies
    23
    Views
    783

    I sure hope it does. I *really* want quick &...

    I sure hope it does. I *really* want quick & easy pasting of pictures. vBulletin makes such a simple thing way too complicated.





    FWIW, vBulletin also came with many annoying features...
  47. The links and files and other details mentioned...

    The links and files and other details mentioned in this answer are for Teensy 3.6.

    Edit WireKinetis.cpp if you want to control the clock speed settings.

    For documentation about the "F"...
  48. Replies
    2
    Views
    145

    I tried ShiftPWM using its "ShiftPWM_RGB_Example"...

    I tried ShiftPWM using its "ShiftPWM_RGB_Example" and the test hardware I built years ago with six 74HC595 chips and RGB LEDs.

    I had the edit the example like this to make it compile.



    ...
  49. Can you show us photos and details of the...

    Can you show us photos and details of the hardware you're actually using?

    This code is complex and honestly, I can't follow what is it doing and I can't understand your explanation of what you...
  50. Addresses 0 to 7 are supposed to be broadcast...

    Addresses 0 to 7 are supposed to be broadcast addresses which all I2C chips hear. So if you have any other I2C devices connected, I would imagine address 0 could cause issues.

    I'm also struggling...
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4