Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: Alex4455

Search: Search took 0.00 seconds.

  1. Replies
    670
    Views
    61,467

    ok, I understand you, I will try to figure it...

    ok, I understand you, I will try to figure it out.
    thank you again for your time!
  2. Replies
    670
    Views
    61,467

    tonton81, maybe you will have a free minute, can...

    tonton81, maybe you will have a free minute,
    can you show me how to receive data from a block please?
    with not a lot of sample code?
  3. Replies
    670
    Views
    61,467

    Yes fine! Thank you!

    Yes fine! Thank you!
  4. Replies
    670
    Views
    61,467

    Thank you for your reply! but for me it is...

    Thank you for your reply!
    but for me it is difficult, I cannot do that, I lack knowledge :(
    I plan to send two commands sequentially,
    first online, then offline, probably this is not correct, but...
  5. Replies
    670
    Views
    61,467

    yes, now thanks to you, I understood everything...

    yes, now thanks to you, I understood everything :)
    I am very grateful to you for your help!
    and if, can you tell me how to write the code correctly, for these purposes ?
    I will be your debtor!
  6. Replies
    670
    Views
    61,467

    wow .... found a bug !!! I had it like that: ...

    wow .... found a bug !!!

    I had it like that:
    msg.buf[0] = 0x01;
    msg.buf[1] = 0x01;

    did so:
    msg.buf[0] = 0x01;
    msg.buf[1] = 0x00;
  7. Replies
    670
    Views
    61,467

    yes, this is the document I use, but it turns...

    yes, this is the document I use,
    but it turns out that nothing works, I am sure that I am doing something wrong,
    but I can't understand what am I doing wrong? if the error is in the team, how...
  8. Replies
    670
    Views
    61,467

    Power Supply Huawei R4850 24518

    Power Supply Huawei R4850
    24518
  9. Replies
    670
    Views
    61,467

    tonton81, I am very grateful to you for...

    tonton81, I am very grateful to you for participating in my problem!
    this is the data I accept using IFCTsimpleFIFOPolling.ino
    24516
    and wto such with the help IFCTsniffer.ino
    24517
    but I don't...
  10. Replies
    670
    Views
    61,467

    I've been fighting this for two weeks now, I...

    I've been fighting this for two weeks now, I broke my whole head,
    I can't imagine which way to dig ...

    I tried to connect through such a module, there is a delay ..
    24514
    there is clearly...
  11. Replies
    670
    Views
    61,467

    2.0-2.5 volts, these levels correspond to Teensy,...

    2.0-2.5 volts, these levels correspond to Teensy,
    I think it is possible that additional commands are needed for the block R4850...
  12. Replies
    670
    Views
    61,467

    unfortunately I don't understand a lot, I have no...

    unfortunately I don't understand a lot, I have no experience with these devices,
    I use this wiring diagram ..
    24512
  13. Replies
    670
    Views
    61,467

    tonton81, can I somehow disable data reception?...

    tonton81, can I somehow disable data reception?
    I only need to transfer data,
    maybe then the transmission speed will increase?

    i made simple code, but the effect is the same, the delay when...
  14. Replies
    670
    Views
    61,467

    unfortunately it gives nothing :(

    unfortunately it gives nothing :(
  15. Replies
    670
    Views
    61,467

    unfortunately there are no changes, the delay...

    unfortunately there are no changes, the delay remains the same 60 seconds (((
  16. Replies
    670
    Views
    61,467

    please tell me where to install this code ? ...

    please tell me where to install this code ?

    msg.flags.extended = 1;
    I use Teensy 3.2, this code throws an error

    can1.setClock(CLK_60MHz);
  17. Replies
    670
    Views
    61,467

    I am very grateful to you for your answer! but,...

    I am very grateful to you for your answer!
    but, I am very bad at programming (((
    can't figure out what i need to do?
  18. Replies
    670
    Views
    61,467

    Hi, please, tell me, what am I doing wrong?...

    Hi,
    please, tell me, what am I doing wrong?
    when the temperature of the external device rises, the power supply R4850 must reduce the output voltage,
    the code works, but when switching the voltage...
  19. Replies
    0
    Views
    119

    Teensy 3.2 and Power Supply R4850

    Hi, dear.

    please tell a newbie how to switch between two voltages 44 and 55 volts in the R4850 unit,
    I am using a Teensy 3.2 controller board, it has a CAN bus, I really want to see the example...
Results 1 to 19 of 19