Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: defragster

Page 1 of 10 1 2 3 4

Search: Search took 0.07 seconds; generated 54 minute(s) ago.

  1. Should be faster - not sure what i2c rate is in...

    Should be faster - not sure what i2c rate is in use but 2 Mbaud would cover it, both can transmit in parallel and no addressing overhead to select one device while the other waits.

    In :...
  2. Replies
    270
    Views
    2,362

    I got a second AMAZON LAN USB dongle today. What...

    I got a second AMAZON LAN USB dongle today. What can I do with 2 Teensys trading messages to test throughput?

    Is the fBench Send/Receive symmetric WRT how the Teensy responds send and receive to...
  3. Analog sensor? 2 bytes per sample? 8,000...

    Analog sensor? 2 bytes per sample? 8,000 bytes/second? May need a byte to ID each sensor as well? 12,000 bytes/sec? Much less if a packed array of digital data.

    Try connecting Serial 1 of...
  4. Was a particular SN65 device purchased - or wired...

    Was a particular SN65 device purchased - or wired directly to a chip?

    Scanning the SN65 chip doc it seems there are ways to start the device in lower power mode - where it won't try activating on...
  5. Replies
    8
    Views
    223

    @AidanP - if you are still considering this - not...

    @AidanP - if you are still considering this - not sure if this Lua-interpreter-example would allow the Teensy 4.0 nodes to run this interpreter and take code on the fly for the cluster?

    No...
  6. Replies
    2
    Views
    420

    The 1062 is the 1060 in the shipping REV #2...

    The 1062 is the 1060 in the shipping REV #2 version.
  7. @FRDM4236 :: Got the FRDM4236 board...

    @FRDM4236 :: Got the FRDM4236 board in today's mail. Looks good - amazing so many wires already pulled across the board!

    Not sure there is room for them already - mixing USB anywhere past the...
  8. A bit more of a forum search may find another...

    A bit more of a forum search may find another example - seems there was one more with better detail than that.

    it is one thing I've not done much with so haven't understood the new scheme yet. And...
  9. There is another post recently regarding PINS and...

    There is another post recently regarding PINS and perhaps the \hardware\teensy\avr\cores\teensy4\imxrt.h and also the schematic - that will have more info on the four PORTS and the pins presented as...
  10. The T_4 of course uses a 1062. It was designed...

    The T_4 of course uses a 1062. It was designed and documented as 1060.

    AFAIK Paul noted two MCU revs were done for the 1060 > 1061 > 1062 is the final production unit. { same with 1050> 1051>...
  11. Replies
    2
    Views
    33

    There is a test note linked here in Post #4 for...

    There is a test note linked here in Post #4 for Freq Count in the T_4 Beta thread : not indicated that FreqCount Library resolved for Teensy 4 use at this time:
    ...
  12. There are some tips in at least one 'PORT' post...

    There are some tips in at least one 'PORT' post in the last week or so.

    Not sure if this is the best post?: port-and-toggle-question-T4
  13. Replies
    4,310
    Views
    457,757

    Good feedback - the Buddhabrot sketch is...

    Good feedback - the Buddhabrot sketch is courtesy of @mjs513. The IDE setting of 1008 actuals codes to 996 through the TD 1.48 setup. It can be changed there.

    Seems noteworthy that over 75C...
  14. Replies
    5
    Views
    84

    Not sure if this OSH board was in the linked...

    Not sure if this OSH board was in the linked page: oshpark.com/shared Teensy 3.2 USB v2

    It wouldn't arrive quickly - but should provide a good fix in the end.

    I have one here from an order I...
  15. Replies
    16
    Views
    134

    That is interesting and should give Paul...

    That is interesting and should give Paul something to work with as far as info.

    I noticed during Beta that the MCU could seem USB Serial or loop() stalled, but _isr active when I was working out a...
  16. Replies
    270
    Views
    2,362

    Re POWER tests - with copper heat sink this was...

    Re POWER tests - with copper heat sink this was at 912 (?) MHz - posted on T4_Beta thread:


    >> Starting two T4's hit 208 or 215 mA as it comes up before USB LAN adapter is connected.
    - nothing...
  17. Replies
    16
    Views
    134

    Yes, sorry to drop that and run. Here is that...

    Yes, sorry to drop that and run.

    Here is that coded to pin #19 { #define SOME_PIN 19 } - it is set PULLUP, so when that pin is set to GND it will break into the _isr and blink { more on that off }...
  18. Replies
    16
    Views
    134

    Interesting - must just be hung then - I didn't...

    Interesting - must just be hung then - I didn't test with triggering a fault.

    If you did a 'pin Change interrupt to an ISR()' that did the blink in the isr() I'm suspecting that changing that pin...
  19. Replies
    58
    Views
    1,814

    Sticky: The lib used there vjmuzik pulled in to good...

    The lib used there vjmuzik pulled in to good effect - but it throws this error during build:


    "T:\\arduino-1.8.9t4\\hardware\\teensy/../tools/arm/bin/arm-none-eabi-g++" -E -CC -x c++ -w -g -Wall...
  20. Replies
    16
    Views
    134

    @blackketter - Interesting - sounds like it is...

    @blackketter - Interesting - sounds like it is faulting?

    To see use this version of the sketch - any <FAST SPAZ> blinking?

    #include <Arduino.h>
    elapsedMillis inw = 0;
    void setup() {
    ...
  21. Replies
    16
    Views
    134

    Not seeing this repro on Windows - LED comes on...

    Not seeing this repro on Windows - LED comes on then goes off with code below.

    @blackketter - does sending one more byte after wake it up - re-reading first post perhaps not as it notes text...
  22. Replies
    5
    Views
    84

    this thread just two days old has links ::...

    this thread just two days old has links :: programming-with-USB-to-Serial-adapter
  23. Replies
    5
    Views
    84

    Yes, there is - this was posted in recent days...

    Yes, there is - this was posted in recent days and the link should still be near the top.
  24. Replies
    3
    Views
    57

    Also - give a look on the forum for Teensy...

    Also - give a look on the forum for Teensy specific tested/developed CAN libraries.

    This one is now well evolved :: FlexCAN_T4-FlexCAN-for-Teensy-4

    Reading/following that thread and working...
  25. Maybe not related - not sure I have a clear pic...

    Maybe not related - not sure I have a clear pic of using "T_3.6 instead" portion... or the rest of what is at hand ...

    Some tested ili9488's were not set up with tri-stated SPI lines - the display...
  26. Replies
    16
    Views
    134

    I didn't think so - but … If that is the case...

    I didn't think so - but …

    If that is the case then having the Host send another Byte or so after '2314' will rewake the receive unit?
  27. Replies
    16
    Views
    134

    Don't suppose any of these three changes make any...

    Don't suppose any of these three changes make any difference?



    #include <Arduino.h>

    void setup() {
    while ( !Serial );
    }
  28. Replies
    16
    Views
    134

    Paul will be doing a full overhaul of the T_4 USB...

    Paul will be doing a full overhaul of the T_4 USB stack to some degree when the functional first pass is replaced with more efficient methods that may double the speed at least once.

    There is a...
  29. Replies
    94
    Views
    2,607

    Bummer on the board loss - and restocking issues....

    Bummer on the board loss - and restocking issues. OshP got me a T4 okay with PCB's in expected time, Never trusted to order Teensy from Amazon. AdaFruit and Sparkfun got a boatload of batch #3 and...
  30. Replies
    270
    Views
    2,362

    Good to see you here @manitou - remembered right...

    Good to see you here @manitou - remembered right it was K66 testing here : teensy3/blob/master/etherraw.ino - apparently this library set has direct MCU ethernet support and was suggested the PJRC...
  31. Replies
    58
    Views
    1,814

    Sticky: @PaulStoffregen>> Two - things ... sort of three:...

    @PaulStoffregen>> Two - things ... sort of three:

    I updated IDE 1.8.9 to TD 1.48 because for some reason the :: 1.8.10 IDE always rebuilds many USBHost ethernet libs even on a small sketch change...
  32. Good work - looks promising - thanks for sharing!...

    Good work - looks promising - thanks for sharing! I may end up doing wires like that to a T4 breakout {the FRDM4236 and the blackketter USB board} - good to see it can work!
  33. Replies
    1
    Views
    48

    perhaps read this post for reference -...

    perhaps read this post for reference - port-and-toggle-question-T4
  34. Replies
    21
    Views
    332

    Good enough to give a much better idea, looks...

    Good enough to give a much better idea, looks very neat versus a pile of POGO's. I was wondering if a wire could snake through to feed pin #23 from one of the other pin #23 points?
  35. Replies
    94
    Views
    2,607

    Looked good ... Ordered a normal thickness set of...

    Looked good ... Ordered a normal thickness set of 3 … $6.30 ...
  36. Replies
    94
    Views
    2,607

    So I got the sub-boards USB/SD - but haven't...

    So I got the sub-boards USB/SD - but haven't RE-ordered a main breakout again yet. Is there a right one to order?
  37. Replies
    94
    Views
    2,607

    Very sad for that T4 - Still work on topside pins...

    Very sad for that T4 - Still work on topside pins right?

    And we lost a chance to hear if board works :(
  38. Replies
    21
    Views
    332

    I ordered one - what is under the Teensy for...

    I ordered one - what is under the Teensy for connectivity? Surface mount contacts? I see the bottom bolts with no through holes for POGO's? And tindie pics don't show.
  39. Replies
    21
    Views
    332

    That looks like a good setup. With updated...

    That looks like a good setup. With updated battery support would be interested.
  40. Only support for Serial as shown is available at...

    Only support for Serial as shown is available at this time for Teensy 4.

    This is work planned/in progress with Paul
  41. Replies
    5
    Views
    99

    It seems I just have to run posted code :) when...

    It seems I just have to run posted code :) when I saw the OP code I wondered how much free time was in loop and it looked like you calculated that so I wouldn't have to.

    Though it is ODD that...
  42. The pin pads on the bottom are discussed in the...

    The pin pads on the bottom are discussed in the T4_BETA thread - seems they are 1mm to match a standard ribbon cable and connector.

    The area is too cramped and close to the USBHost pins so it was...
  43. See original post:...

    See original post: Compatible-SD-card-connector-for-Teensy-4-0

    Closing this to avoid duplication
  44. Replies
    6
    Views
    76

    Indeed SoftPWM is in the list of libraries not...

    Indeed SoftPWM is in the list of libraries not yet updated for Teensy 4.0:

    Teensy-4-0-First-Beta-Test … Post #4
  45. Replies
    270
    Views
    2,362

    Good you put that off until it was stable to test...

    Good you put that off until it was stable to test against. I suppose there may be some subset of 'right size' and 'right regularity' that could be the perfect solution. But easy to see cases where...
  46. Replies
    4,310
    Views
    457,757

    NOTE on temps: Running at 960 MHz the T_4 with...

    NOTE on temps:

    Running at 960 MHz the T_4 with active USBHost noted above to LAN through powered hub maintained 78C today not problem.

    Going to another sketch @luni intervaltimer posted - and...
  47. Yes, that is one of the OSH PCB's that can be...

    Yes, that is one of the OSH PCB's that can be used to fix a lost USB micro for T_3.2 and similar.

    Those Teensy 4.0 bottom pads are connected to a secondary USB engine in the MCU, they cannot be...
  48. T_3.2 does not have USB Host - those are the...

    T_3.2 does not have USB Host - those are the device pins.

    The newer Teensy's have connect board pins to hold connector better. Indeed it is not the best design … but it was the standard …
  49. See this thread - not sure the OSH board is there...

    See this thread - not sure the OSH board is there … but it has notes that should apply:: How-to-repair-a-broken-off-Teensy-3-0-USB-connector
  50. Teensy can only be programmed through the USB...

    Teensy can only be programmed through the USB Micro connector - or {for T_3.2} the equivalent USB pins connected on the underside. There is no mapping through UART Serial or other way to program a...
Results 1 to 50 of 500
Page 1 of 10 1 2 3 4