Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: Spencez

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    2,627

    Nice to see someone else giving this a shot. I...

    Nice to see someone else giving this a shot. I have come a long way since my last post, I will share here shortly. One of the issues I had was that the pads were so close together there wasn't much...
  2. Replies
    49
    Views
    13,494

    Arduino CLI 0.19.0 was just released with support...

    Arduino CLI 0.19.0 was just released with support for pluggable discovery. This is good news, I assume Arduino CLI and Arduino IDE 2.0 Beta are finally ready for Teensy support.
    ...
  3. Replies
    197
    Views
    43,898

    That is a problem. Pin 10 should be pulled high...

    That is a problem. Pin 10 should be pulled high by the MKL02. If this is LOW, I believe pin 9 will also be low which is your power on reset. This means the processor is being held in reset and it...
  4. Replies
    11
    Views
    962

    Are you powering it with a LiPo? I remember...

    Are you powering it with a LiPo? I remember reading that the ESC has regenerative braking and it could damage a power supply so you had to use a LiPo to power it. If so disregard, I just remember...
  5. Replies
    11
    Views
    962

    You could try his code before going ahead and...

    You could try his code before going ahead and buying one although he explains how he only could get it to work with a KISS ESC, not sure the reason. It should work on either of your Teensy versions,...
  6. Replies
    11
    Views
    962

    Are you using a KISS ESC? If so, Give this a...

    Are you using a KISS ESC? If so, Give this a shot.
    https://sbasami-tech.hatenablog.com/entry/2020/08/23/095106
    Specifically this ino....
  7. Replies
    11
    Views
    962

    Did you try pin 4? It looks like ESC 1 should be...

    Did you try pin 4? It looks like ESC 1 should be on pin 4 according to the readme on github.
    25421

    Sorry for the simple question, I will try and look deeper into it tomorrow.
    Which version...
  8. Replies
    11
    Views
    962

    How far did you get with attempting to use the...

    How far did you get with attempting to use the teensyshot library? At first glance it looks as if once you load the program on to the Teensy you need to write a program on the pc which sends data to...
  9. This may do what you need but it is $199....

    This may do what you need but it is $199. https://www.pemicro.com/products/product_viewDetails.cfm?product_id=15320138&productTab=1
    Only other thing I could find is this article....
  10. It's normal. If you do not have a cable connected...

    It's normal. If you do not have a cable connected it will hang forever.

    You can see it on line 293. I believe it was left that way to be consistent with the original Ethernet library but you can...
  11. First thing I found was this. Not sure if this is...

    First thing I found was this. Not sure if this is related but it's worth a shot either disabling the timer before calling parsePacket then re-enabling it. Alternatively call noInterrupts() and...
  12. You can usually put multiple slaves on one SPI...

    You can usually put multiple slaves on one SPI bus and the CS pin will tell the slaves when they are being communicated with. I believe you should be able to get rid of one of your spi lines and set...
  13. Replies
    1
    Views
    399

    You could use IntervalTimer if you plan to run...

    You could use IntervalTimer if you plan to run these at a fixed interval. This is what I have used to acquire data from SPI and pass data to the main loop....
  14. No problem, hopefully that's the issue. I'm not...

    No problem, hopefully that's the issue. I'm not even sure if UDP_TX_PACKET_MAX_SIZE does anything inside of the library, I quickly searched for it but I didn't get any hits. I would assume it's just...
  15. I noticed you are running outside of the leds...

    I noticed you are running outside of the leds array, the length is 14 and you are accessing up to packetSize which is 24,24,27. It could be causing your problem. The garbage data in your third...
  16. Replies
    0
    Views
    228

    USB Device has Malfunctioned

    I have a project in which I am powering a Teensy 4.0 with 5V directly from a power supply and I have the trace cut so I can still use the USB for acquiring data over serial. I noticed recently that...
  17. Replies
    13
    Views
    2,627

    I will probably upload the files and/or post it...

    I will probably upload the files and/or post it on OSHPark. It requires hot air, good soldering skills and flux.



    I would love if they did this. I feel as if they are waiting until they make...
  18. Replies
    13
    Views
    2,627

    Teensy 4.1 Debug Mod Project

    I have been working on a Teensy 4.1 debugger mod for a month or so now and I figured it was in a good place to share my progress. This project started by de-soldering the MKL02 chip, soldering magnet...
  19. Replies
    5
    Views
    1,263

    That's great Paul! I will be sure to use these...

    That's great Paul! I will be sure to use these for my board. Is there a recommended footprint for the header? I'm sure I could use a similar part's footprint and it would be fine but just to be safe....
  20. No problem. Hope it is really as easy as swapping...

    No problem. Hope it is really as easy as swapping out a part rather than needing another pcb manufactured. I have been fine so far with user libraries, but it is always good to double check them for...
  21. Replies
    5
    Views
    1,263

    Thanks for the suggestion, this is what I am...

    Thanks for the suggestion, this is what I am after for sure. I have not gotten around to making the next revision of my board yet but I will definitely consider these. Since I have posted this I...
  22. Looking at the J0011D01BNL datasheet, it looks...

    Looking at the J0011D01BNL datasheet, it looks like the pinout is different between the J0011 and the J1B1211CCD that PJRC uses?
    Here is the J0011
    23192

    and J1B1211CCD
    23193

    Cable side is...
  23. Replies
    5
    Views
    1,263

    Teensy 4.1 Ethernet pins + socket

    I am making an addon pcb for the teensy 4.1 which will need to passthrough the 48 outer teensy pins along with the 6 ethernet pins. I will use two of the 24x1 Sockets on the pjrc store to pass...
Results 1 to 23 of 23