Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: KOC62

Search: Search took 0.00 seconds.

  1. Thread: rc transmitter

    by KOC62
    Replies
    7
    Views
    284

    I too was looking for an R/C transmitter-receiver...

    I too was looking for an R/C transmitter-receiver for a small rover. A friend uses one similar to this;...
  2. I've worked on an organ that used a cylindrical...

    I've worked on an organ that used a cylindrical magnet in the end of each pedal and a reed switch would close a contact when the pedal was depressed. Here is one idea;...
  3. Thread: Midi + Solenoid

    by KOC62
    Replies
    4
    Views
    187

    Ok, that project/link can help you. The link uses...

    Ok, that project/link can help you. The link uses an UNO but you could also use a Teensy but the pin numbers may be different. I haven't used my Teensy yet thus can't guide you in substituting the...
  4. Thread: Midi + Solenoid

    by KOC62
    Replies
    4
    Views
    187

    Yes, a Teensy can do it. Have a look here;...

    Yes, a Teensy can do it.
    Have a look here; https://learn.adafruit.com/midi-solenoid-drummer/overview
  5. Replies
    3
    Views
    252

    Yes, the series resistance can cause a slow...

    Yes, the series resistance can cause a slow start-up or "sleepy crystal". I found this article helpful, https://www.electronicdesign.com/analog/fundamentals-crystal-oscillator-design
  6. Replies
    57
    Views
    1,847

    Where did you see the 250ma current spec? On page...

    Where did you see the 250ma current spec? On page 6 I found 25ma.(https://www.nxp.com/docs/en/data-sheet/K66P144M180SF5V2.pdf)
    Not familiar with the Teensy regarding slew rate control.

    The...
  7. Somebody might be able to help, but first;...

    Somebody might be able to help, but first; "Always post complete source code & details to reproduce any issue!"
  8. Replies
    57
    Views
    1,847

    I wasn't able to make my circuit simulation...

    I wasn't able to make my circuit simulation malfunction using the pulse width values you gave. So, perhaps I'm not simulating it correctly? I wonder what your scope output does look like using this...
  9. Replies
    57
    Views
    1,847

    I'd be interest to see a 'scope shot of a data...

    I'd be interest to see a 'scope shot of a data stream including your sync. Apparently LTSpice has a way of using a data file to stimulate the circuit so one can see what the output would be with such...
  10. Replies
    57
    Views
    1,847

    Before you connect a CD4050, try to see if there...

    Before you connect a CD4050, try to see if there is a negative dc level in your output. My data sheet says not to go below 0.5V input. As Paul mentioned its possible to shift the dc point via...
  11. Replies
    57
    Views
    1,847

    Perhaps you have. How about using an AC coupled...

    Perhaps you have. How about using an AC coupled circuit with clamping diodes and an emitter follower, like below? You can fiddle with the values to get a good waveform. I use LTSpice for a quick...
  12. Replies
    57
    Views
    1,847

    I didn't do any testing, but drew the diagram to...

    I didn't do any testing, but drew the diagram to provide a proof of concept. Your selection of a high speed opto is better since it is designed to work with 3.3V.
    The 330 ohm was an arbitrary value...
  13. Replies
    57
    Views
    1,847

    That opto is too slow. I was thinking of a...

    That opto is too slow. I was thinking of a 6N137M. You may need to fiddle with the resistor values to get the desired rise/fall times. Also, it is uncertain as to how much delay this circuit produces...
  14. Replies
    57
    Views
    1,847

    I wonder if a 6N137 optcoupler would work as your...

    I wonder if a 6N137 optcoupler would work as your level shifter. It may work at 3.6V for Vcc, although the datasheet says 4.5V minimum. It would provide ground loop protection for your keyboard.
  15. Replies
    23
    Views
    1,279

    Glad to hear its working for you. Further...

    Glad to hear its working for you.
    Further refinements could include an autoranging circuit to bring the shunt voltage closer to the maximum analog input of the Teensy, but you may not require such...
  16. Replies
    23
    Views
    1,279

    What voltage do you measure from either two wires...

    What voltage do you measure from either two wires and ground when the battery is charging, or when the equipment is run from battery only?
    Your planned circuitry will need to compensate for this...
  17. Replies
    7
    Views
    1,008

    I still have one of those clocks.

    I still have one of those clocks.
  18. Replies
    1
    Views
    262

    You need to isolate the motor voltage or current...

    You need to isolate the motor voltage or current that you wish to analyse. This can be done via a suitable transformer, or an isolation current to voltage transducer (hall effect device?), along with...
  19. Does your tuner have a means to determine how...

    Does your tuner have a means to determine how many cents it's off, or be able to set it to x-cents off?

    Years ago I worked with an organ technician who had a "home built" organ tuner that showed...
  20. Hard to say with no actual hardware (or...

    Hard to say with no actual hardware (or schematic) in front of me. If all the "ducks" need to be aligned precisely before it works I would expect a timing issue somewhere, or faulty code. Decoupling...
  21. Replies
    11
    Views
    1,525

    Thanks Theremingenieur.

    Thanks Theremingenieur.
  22. Replies
    11
    Views
    1,525

    What values do you recommend?

    What values do you recommend?
  23. Replies
    11
    Views
    1,525

    Sorry, ... beginner's oversight. I didn't scroll...

    Sorry, ... beginner's oversight. I didn't scroll down far enough, where the pots are read and thus connected.
  24. Replies
    11
    Views
    1,525

    Looks like an interesting project. I don't see...

    Looks like an interesting project. I don't see where you connect the pots to the Teensy in your code.
  25. I was dabbling with PID V1 a couple of years ago...

    I was dabbling with PID V1 a couple of years ago using an Arduino UNO with a standard 16MHZ clock. My notes said that PID.compute() took 80 usec. The default myPID.SetSampleTime () is 100 millisec....
  26. Replies
    12
    Views
    3,913

    I'm interested in how you made/cut the panel for...

    I'm interested in how you made/cut the panel for the switches and the labelling. I often don't get past doing "a proof of concept" because of a lack finishing details and equipment. Thanks.

    Peter.
  27. Replies
    2
    Views
    691

    Also see this for a direct connection to an 8X8...

    Also see this for a direct connection to an 8X8 RGB module, https://github.com/marcmerlin/LED-Matrix/
  28. Replies
    7
    Views
    1,682

    How about the CD4511? ...

    How about the CD4511? https://www.digikey.com/product-detail/en/texas-instruments/CD4511BE/296-2072-5-ND/67341
  29. Replies
    16
    Views
    2,776

    No, not yet. It may be awhile before I get to an...

    No, not yet. It may be awhile before I get to an audio teensy project, as I have a number of other projects on the go.
  30. Replies
    16
    Views
    2,776

    I use this unit ...

    I use this unit for similar reasons for my headphone listening/testing of various audio devices. It has a gain switch for selecting High and Low to cover most situations.
  31. The datasheet says minimum 3.5V swing, but...

    The datasheet says minimum 3.5V swing, but typically 4V swing, for a 5V DC supply.
    I'd use a 3.3V power supply and then evaluate what the MSGEQ7 is not doing so well at 3.3V.
  32. Replies
    23
    Views
    10,323

    Thanks, Paul. I thought that it might have been...

    Thanks, Paul.
    I thought that it might have been removed due to some incompatibility with the new Lib, meaning that "NewPing" couldn't be used.
  33. Replies
    23
    Views
    10,323

    Libs removed: NewPing. Is there a substitute...

    Libs removed: NewPing.
    Is there a substitute for those wanting a "NewPing" function?
    I am in the process of building a 2WD Arduino rover with an Ultrasonic sensor. I'm currently planning to use an...
  34. Replies
    3
    Views
    847

    I could only find this...

    I could only find this which is for an Arduino, but you may be able to use your Teensy 3.6 board too. I don't have the changes you would need to make.
  35. Replies
    9
    Views
    2,088

    Thanks for the link. I'll take a look.

    Thanks for the link. I'll take a look.
  36. Replies
    9
    Views
    2,088

    Hmmm.... I may become interested in this project....

    Hmmm.... I may become interested in this project. Our church has an old Johannus OPUS 1100 organ that has a MIDI out only, which no one uses. I've often wondered what that port provides. Maybe just...
  37. Replies
    3
    Views
    847

    It isn't clear to me what you consider to be "a...

    It isn't clear to me what you consider to be "a good idea", as I don't clearly know what this project is connected to. Simply connecting your 3.5 mm jack to an analog input is too simplistic, and not...
  38. Could there not be a DC bias on the probes? I...

    Could there not be a DC bias on the probes? I would agree that the right-side diagram of yannick's schematic uses AC coupling to avoid such a DC. The article I linked in a previous post (#48) also...
  39. Jumping in here, rather late .... I'm not fond...

    Jumping in here, rather late ....
    I'm not fond of your electrode - Teensy interface. I would prefer using a "instrumentation amplifier" chip.
    Also, this article...
  40. Replies
    15
    Views
    2,483

    Thanks. No its not a serious issue, just an...

    Thanks.
    No its not a serious issue, just an observation on my part. It wouldn't significantly change the total current as most of the current is consumed by the IC.
  41. Replies
    15
    Views
    2,483

    I'm not a frequent viewer here, but I don't know...

    I'm not a frequent viewer here, but I don't know what a "chamberlain" filter is. I do know about the biquad.

    Did your stepdad work on vacuum tubes?
    The resistor values of your opamp circuit...
Results 1 to 41 of 41