Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: mah

Search: Search took 0.00 seconds.

  1. Replies
    243
    Views
    28,800

    Pin compatible with t4.1 but extra outside rows...

    Pin compatible with t4.1 but extra outside rows seems ideal to me! maybe change sdcard to pins instead of the slot.
  2. Bel Magnetic SI-46001-F as ethernet connector for teensy 4.1

    Hi, designing my first pcb, for teensy 4.1, i want a vertical Ethernet connector, i have made the design using the "Bel Magnetic SI-46001-F", as its one of the few vertical i found.

    Could anyone...
  3. Replies
    1
    Views
    178

    Spi devices with different clock speeds

    Hi, im wondering how to handle spi when chips have diffrent max clock speeds.

    should i change clock speed between communicating with different chips?
    Or should i use two buses with diffrent...
  4. Replies
    4
    Views
    373

    "Since this chip is a special bi-directional...

    "Since this chip is a special bi-directional level shifter it does not have strong output pins that can drive LEDs or long cables, it's meant to sit on a breadboard between two logic..." I guess a...
  5. Replies
    4
    Views
    373

    Yeah, I know Paul suggested that the some of...

    Yeah, I know Paul suggested that the some of those was not a good option for some applications, but don't remember the specifics right now. Maybe it will be fine
  6. Replies
    4
    Views
    373

    True bidirectional logic level shifter

    Hi, I'm want to send and receive eurorack/synth gates with a teensy 4.1, the gates should be 5v but as the teensy is 3.3 v so I need to shift both up and down, and I also want to use software to...
  7. Replies
    3
    Views
    400

    wow thx! cleared up quite a lot of things! ...

    wow thx! cleared up quite a lot of things!

    Just to be clear, this should theoretically be the most efficient method of connecting SPI devices?
    ---------------------
    SPI0:
    MISO0
    MOSI0
    SCK0...
  8. Replies
    3
    Views
    400

    SPI pins teensy 4.1

    I'm using a teensy 4.1, and got some questions about SPI:

    Is it possible to use both "miso,mosi,sck,cs" (pins: 12,11,13,10) and "miso1,mosi1,sck1,cs1" (pins: 1,26,27,0) at the same time?...
  9. Replies
    3
    Views
    235

    Thanks, i was just wondering, this might be a bad...

    Thanks, i was just wondering, this might be a bad idea to, but if i connected busy to CNV, would that make it do a conversion every time its not busy?
  10. Replies
    3
    Views
    235

    LTC2335-16 CNV input

    Hi, I'm using a LTC2335-16 ADC in a project and I am a bit confused about what to do with the CNV input, from what I read the ADC conversation happens when the ADC gets input on the cnv pin, should I...
  11. Replies
    20
    Views
    5,527

    Yeah, thanks, could not find a schematic so i...

    Yeah, thanks, could not find a schematic so i looked at other schematics. gonna remove the 3.3v, and the resistor.
    Dont know much about the SI-46001-F either, just picked it because i needed a...
  12. Replies
    20
    Views
    5,527

    20799 Is this right? :confused:

    20799 Is this right? :confused:
  13. Some progress, if i upload example...

    Some progress, if i upload example "interface_16x16" and send midi from ableton to channel 1 on virtual cable 7 and then to channel 10 on virtual cable 7, the device connected to teensy's usb host...
  14. Ok, still no luck. i have used the...

    Ok, still no luck. i have used the interface_16x16 example just to know that its not my code. When connecting a ableton push mk1 and a beatstep to the usb host on a teensy, and connect the teensy as...
  15. i changed to a really short usb cable, and i...

    i changed to a really short usb cable, and i worked until i reset the teensy
  16. Yes, i mentioned i set it as midi+serial, gonna...

    Yes, i mentioned i set it as midi+serial, gonna clarify in my post. and as the teensy can receive midi trough the usb hot port im thinking there error is somewhere else
  17. UsbHost, device send messages but does not receive

    Hi, i have a beatstep connected to teensy via usbhost, no extra circuitry just gnd, 5v, d+ and d- stright from teensy to beatstep, the pads and knobs send midi to the teensy it works fine, but i cant...
Results 1 to 17 of 17