Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: e_l_tang

Search: Search took 0.00 seconds.

  1. Replies
    695
    Views
    692,261

    I did investigate alternatives to Wire, but like...

    I did investigate alternatives to Wire, but like you said they're all lacking in one way or another.
  2. Replies
    695
    Views
    692,261

    Well, given your experience and their relative...

    Well, given your experience and their relative simplicity, I can't imagine that it'd be much of a challenge for you if you did decide to do it.
  3. Replies
    695
    Views
    692,261

    It seems that writing a TWI driver is harder than...

    It seems that writing a TWI driver is harder than I thought. Do you have plans to port this library to the AVR Teensies?
  4. Replies
    695
    Views
    692,261

    I want to make a general-purpose driver, one that...

    I want to make a general-purpose driver, one that will fit the needs of all my current and future projects. In my current project there is a single master, so no, it is not a hard requirement that...
  5. Replies
    695
    Views
    692,261

    I'm just trying to make my driver future-proof so...

    I'm just trying to make my driver future-proof so that I don't ever have to find myself making substantial changes to it. I'm thinking of a case where not all of what's going to be sent during a...
  6. Replies
    695
    Views
    692,261

    So then would you say that the most flexible way...

    So then would you say that the most flexible way of implementing repeated starts in a driver is the one you chose?
  7. Replies
    695
    Views
    692,261

    The code I'm writing is actually for more than...

    The code I'm writing is actually for more than just a one-off project, so I would like to adhere to recommended practice as much as possible. I'm going to see if I can write my own TWI driver. In...
  8. Replies
    695
    Views
    692,261

    Even if it works, is it recommended practice?...

    Even if it works, is it recommended practice? Also, doesn't keeping SCL low for long periods waste power?
  9. Replies
    695
    Views
    692,261

    Is it safe to send a message without ending it...

    Is it safe to send a message without ending it immediately with a stop or a repeated start? I know that this library allows you to leave the stop off the end of a message so that the next start is...
  10. Somehow it's working now. I'm not sure what went...

    Somehow it's working now. I'm not sure what went wrong.
  11. I'm using a Teensy 2.0.

    I'm using a Teensy 2.0.
  12. HalfKay cannot be entered from software consistently

    The code from this page leaves the Teensy running neither the application nor the boot loader if an external reset has happened (the reset button has been used) since the last power-on reset.
  13. Replies
    7
    Views
    2,859

    The problem is that I plan to port my project to...

    The problem is that I plan to port my project to many, many more chips, some of which are not supported by the Arduino IDE. If I take the easy way now, I'm going to have to face freeing my entire...
  14. Replies
    7
    Views
    2,859

    Many thanks for the answers, Paul. I'm sure they...

    Many thanks for the answers, Paul. I'm sure they will all be helpful when I get around to implementing the functionalities I asked about, but I think right now I'll have my hands pretty full trying...
  15. Replies
    7
    Views
    2,859

    Using Teensyduino's USB library

    I'm writing a custom keyboard firmware for the Teensy 2.0 and I'm planning to use Teensyduino's USB library. However, it's embedded deep inside Teensyduino along with a lot of other libraries that I...
Results 1 to 15 of 16