Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: hobi

Search: Search took 0.00 seconds.

  1. Replies
    76
    Views
    21,866

    Well, what you really need is a iron with fine...

    Well, what you really need is a iron with fine tip , of course, but the most important thing is a GOOD flux.
    You almost do not need solder , as most of the time the PSC almost has enough....
  2. @AndyCap thank you for the Vscode tips. ...

    @AndyCap

    thank you for the Vscode tips.

    Looks there needs to be a little bit more "packaging" to get a clean version of this debugging feature. I think this definitely makes the overall system...
  3. Replies
    16
    Views
    744

    @Glaskows, this is what you look for I think, but...

    @Glaskows, this is what you look for I think, but in 16 bits :
    https://www.nxp.com/docs/en/application-note/AN5313.pdf
  4. Hi ! Looking at this thread, i find this really...

    Hi !
    Looking at this thread, i find this really excellent.
    Am I making a too quick assumption thinking i can get inline debug capability within Vscode/Platformio, which to my knowledge is based on...
  5. Replies
    16
    Views
    744

    This app note might help... ...

    This app note might help...
    https://www.nxp.com/docs/en/application-note/AN5280.pdf
  6. Replies
    16
    Views
    744

    Hmmm really interesting. Let’s see what we can...

    Hmmm really interesting. Let’s see what we can get out of flexio...
  7. Replies
    16
    Views
    744

    Hi there. The whole purpose of the tft interface...

    Hi there. The whole purpose of the tft interface is to be able to cope with slightly larger tft than 320x480. Sizes like that or smaller have built in frame buffer and the writing speed through even...
  8. Replies
    16
    Views
    744

    Hi. Quick question: When you say: Sadly, the...

    Hi. Quick question:
    When you say: Sadly, the parallel lcd data bus run through the GPIO B0_xx and B1_xx (for wider buses) > do you mean that there is no way to use the built in lcd contrôler due to...
  9. Ok, seems indeed that some checks are needed. I...

    Ok, seems indeed that some checks are needed. I will test with 3 async clocks, and will check for errors. Underclocking may not be the best thing. Let's see and thanks for the warning.
  10. Yep this is indeed what I understood! Thanks for...

    Yep this is indeed what I understood! Thanks for the confirmation. I can also undeclock the cpu... not sure though that this will lower the 60mhz clock...
  11. Hi Paul, Thank you for giving me a so fast...

    Hi Paul,
    Thank you for giving me a so fast answer.
    IJust to be clear, this would mean that I will get a time measure accurate @ 1clk cycle at 60Mhz... which is really more precision than what I...
  12. FreqMeasureMulti on Teensy 3.6 : precision over a few minutes?

    Good Morning,

    I would like to use a Teensy 3.2 or 3.6 to perform timings measurement of 3 digital signals.
    Those signals are expected to be digital pulses with a frequency of 1.5Khz up to 6Khz,...
  13. Replies
    479
    Views
    291,482

    Hi folks, Just wanted to be sure the simple...

    Hi folks,

    Just wanted to be sure the simple code i wrote does what it intends to do. Simple single ended ADC acquisition at 6000Hz, precisely timed, for signal processing.

    Thank you for your...
  14. Replies
    479
    Views
    291,482

    OOOps, you are right, I got confused with the...

    OOOps, you are right,

    I got confused with the naming. These are DMA interrupts, not ADC ones! Ok, very clear. Thanks for the reply!

    Olivier.
  15. Replies
    479
    Views
    291,482

    KurtE, I will have a look, but I think it will...

    KurtE,

    I will have a look, but I think it will help.

    I have one basic question. For me the dma should work fully in the background without any cpu need. Do we really need to have an adc isr ??...
  16. Replies
    479
    Views
    291,482

    Hello , I am looking to use Teensy 3.2 with...

    Hello ,

    I am looking to use Teensy 3.2 with the ADC to acquire data, to then run some signal processing. I read the thread, and trid to find relevant information with the search engine, but I...
Results 1 to 16 of 16