Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: markkimball

Search: Search took 0.00 seconds.

  1. Another approach would be to use the CPU, but use...

    Another approach would be to use the CPU, but use an interrupt routine to perform the bit-bang. One of the spare timers could generate an interrupt every 250ns to output the next bit in your serial...
  2. Replies
    8
    Views
    561

    Thanks to all for the input. I loaded...

    Thanks to all for the input.

    I loaded lubuntu-18.04LTS on the old laptop. I believe it's the last "lightweight" 32-bit Ubuntu distro. Arduino and Teensyduino appear to run OK, but the old laptop...
  3. Replies
    8
    Views
    561

    The problem is that Teensy.exe requires a library...

    The problem is that Teensy.exe requires a library that's not present -- libgtk-3.so.0. When called, it quietly exits so it wasn't immediately obvious what was going on.

    Unfortunately, this...
  4. Replies
    8
    Views
    561

    Editing platform.txt found in...

    Editing platform.txt found in arduino-system-follder/hardware/teensy/avr to eliminate calls to teensy_secure got rid of the error messages relating to teensy_secure. So perhaps my missing library...
  5. Replies
    8
    Views
    561

    As long as teensy_secure has to run in order to...

    As long as teensy_secure has to run in order to compile Teensy code, I am in fact dead in the water. Regardless if it makes a lockable version or not, that utility apparently is called into action. ...
  6. Replies
    8
    Views
    561

    Peculiar Teensyduino problem

    I recently installed copies of the most recent Arduino IDE (1.8.16) and Teensyduino 1.55 on a Dell D600 running Puppy Linux (it works pretty well on old computers). The combination _seems_ to work...
  7. A resistor in the gate line also will help...

    A resistor in the gate line also will help suppress oscillations that could occur when the device is switching. Regarding the sleep/hibernate question, if the digital pin becomes a high impedance...
  8. Replies
    11
    Views
    912

    SCK2, CS2, MOSI2 and MISO2 are available on the...

    SCK2, CS2, MOSI2 and MISO2 are available on the back of the T4.0. They are pins 37, 36, 35 and 34 respectively. Not real easy to use, being part of the SD card socket footprint. However, I have a...
  9. Replies
    11
    Views
    912

    That's an interesting idea. Examination of the...

    That's an interesting idea. Examination of the reference manual indicates that there are 4 LPSPI blocks, and they can be individually configured as a Master or Slave. I'll have to look at the IOMUX...
  10. Replies
    11
    Views
    912

    The performance of a QSD-based SDR is highly...

    The performance of a QSD-based SDR is highly dependent on the ADC. While the built-in ADC's sample rate is fast enough to permit decoding wideband FM, losing 4 bits (12 vs. 16) isn't something I...
  11. Replies
    11
    Views
    912

    Some online searching has indicated that the dual...

    Some online searching has indicated that the dual data mode for SPI transfers data on both the rising and falling edge of SCK. For instance, see...
  12. Replies
    11
    Views
    912

    Table 50-9 in the processor reference manual...

    Table 50-9 in the processor reference manual shows an example of a FlexIO setup configured as an SPI master. That would be a good starting point. It should be possible to allocate a third shifter...
  13. Replies
    11
    Views
    912

    Specifically, the 4 series. When you say "LPSPI...

    Specifically, the 4 series. When you say "LPSPI chapter" are you referring to the data sheet?
  14. Replies
    11
    Views
    912

    SPI variant question

    I've been looking at fast dual ADC chips, with a possible SDR application for the I/Q channels. Most audio codecs run out of gas above 192KSPS (if you want to stick with the data sheet anyway) but...
  15. Replies
    2
    Views
    483

    Thank you for the information. I'll take a look...

    Thank you for the information. I'll take a look at the info on github.

    Mark
  16. Replies
    2
    Views
    483

    tlv320aic3206 audio ADC?

    First post here. Owner of a Teensy 4.0, writing code with the Arduino IDE on Ubuntu 18.04.

    I'm working on a couple of non-audio applications* that need 192KSPS@16 bits, which I believe eliminates...
Results 1 to 16 of 16