Forum Rule: Always post complete source code & details to reproduce any issue!

Search:

Type: Posts; User: Ando_Shy

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    161

    Hey thanks! I'll give it a try. -Andrew

    Hey thanks! I'll give it a try.
    -Andrew
  2. Replies
    2
    Views
    161

    Teensy 3.2 Reset Pad fell off...

    Good day,

    I was working on a project that required the teensy 3.2 reset pad. Turns out this pad is like super fragile... and if fell off. I swear I barely touched it... :( Anyways, Is there...
  3. Hey Vjmuzik, Thanks again for the info! I was...

    Hey Vjmuzik,
    Thanks again for the info! I was hoping I could find a simpler solution (even if it's quick and dirty) as things are already pretty cramped in my enclosure as it is and I need some...
  4. touchRead value bouncing all over the place

    Good day,

    I am working with a motorized fader and have been trying to use to touchRead function as a way to interrupt the fader when it is in motion. I've been experiencing some odd (maybe)...
  5. Replies
    3
    Views
    390

    thank you vjmuzik! I'll give this a try and...

    thank you vjmuzik!
    I'll give this a try and report back with the results.
    -Andrew
  6. Replies
    3
    Views
    390

    Limit MIDI to just two ports?

    Good day,

    I am working on a project that uses midi and requires 2 ports. Everything is tested and functional using the MIDIx4 profile for teensy. However, in this particular case the additional...
  7. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    So boneheaded mistake wins it! Actually I gotta...

    So boneheaded mistake wins it! Actually I gotta give props to vjmuzik he hit the nail on the head with the first post. The pins on the connectors were flipped, not sure why it didn't work when I...
  8. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    And for the record I have some Vishay 6n138 and...

    And for the record I have some Vishay 6n138 and 6n137 optocouplers if anyone’s had better luck with the latter
  9. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    It prints «*MIDI Input Test*» and then...

    It prints «*MIDI Input Test*» and then «*Inactivity*» every 10 seconds after as it should. I see no fault in the code as written. If it is a code related issue I would guess that it would be more...
  10. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    Thanks Larry, I have already tried slapping a...

    Thanks Larry, I have already tried slapping a resistor on pin 7 as described in the link, but when I get the chance I’m going to go through the data sheet again and try playing with the resistor...
  11. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    The answer is a finite supply of money, and I...

    The answer is a finite supply of money, and I have built many projects including an analogue modular synth, DMX controllers, arduino and teensy based stuff, as well as wireless transmission projects...
  12. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    I don’t have a scope... as I mentioned in the...

    I don’t have a scope... as I mentioned in the original post, I was kinda hoping to find some direction to trouble shoot this without dropping cash on test equipment as it would seem MIDI should be...
  13. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    I have already tried the connector wired in both...

    I have already tried the connector wired in both possible configurations with no change in the result.
  14. Thread: MIDI Troubles

    by Ando_Shy
    Replies
    14
    Views
    2,197

    MIDI Troubles

    Hello,
    I am writing because I spent several hours today trying to get 5-pin MIDI to work with my Teensy 3.2, I followed the schematic located at the PJRC MIDI Library page precisely and am using the...
Results 1 to 14 of 16