KurtE
Senior Member+
I think I have everything synced up. And built again. I also edited the example sketch that at end allows me to quickformat or lowlevelFormat or none...
Running on my Beta Faster board...
So it stays at about the 120-130+kb per second. Now to try again on New chip:
First with the older one I did, even after low level format about 78kb...
Dito for the new one...
Just to make sure same memory on each board, I update the littlefs to print out data about the identification of the chip...
Which you can see the details from screenshot of three TyCommander windows, where all three chips were programmed at the same time
It is almost like maybe the original chip had something run on it that converted it to work in Quad mode and the newer boards are still running ins single or dual pin SPI? Not sure if that
makes sense?
Running on my Beta Faster board...
Code:
C:\Users\kurte\Documents\Arduino\bar\bar.ino Nov 25 2020 17:25:21
Started QSPI_DISK
Bytes Used: 8192, Bytes Total:16777216
Start Big write of 8283312 Bytes......................
C:\Users\kurte\Documents\Arduino\bar\bar.ino Nov 26 2020 06:54:59
Started QSPI_DISK
Bytes Used: 8192, Bytes Total:16777216
Start Big write of 8283312 Bytes.........................
Big write took 62.44 Sec for 8280000 Bytes : file3.size()=0
Big write KBytes per second 132.62
Bytes Used: 8192, Bytes Total:16777216
C:\Users\kurte\Documents\Arduino\bar\bar.ino Nov 26 2020 06:59:44
Started QSPI_DISK
Bytes Used: 8192, Bytes Total:16777216
Start Big write of 8283312 Bytes.........................
Big write took 60.74 Sec for 8280000 Bytes : file3.size()=0
Big write KBytes per second 136.32
Bytes Used: 8306688, Bytes Total:16777216
: q-quickformat, l-lowlevel format, else no format
Bytes Used: 8192, Bytes Total:16777216
C:\Users\kurte\Documents\Arduino\bar\bar.ino Nov 26 2020 06:59:44
Started QSPI_DISK
Bytes Used: 8192, Bytes Total:16777216
Start Big write of 8283312 Bytes.........................
Big write took 64.65 Sec for 8280000 Bytes : file3.size()=0
Big write KBytes per second 128.08
Bytes Used: 8306688, Bytes Total:16777216
: q-quickformat, l-lowlevel format, else no format
.........................................................................................................................
Bytes Used: 8192, Bytes Total:16777216
C:\Users\kurte\Documents\Arduino\bar\bar.ino Nov 26 2020 06:59:44
Started QSPI_DISK
Bytes Used: 8192, Bytes Total:16777216
Start Big write of 8283312 Bytes.........................
Big write took 62.15 Sec for 8280000 Bytes : file3.size()=0
Big write KBytes per second 133.23
Bytes Used: 8306688, Bytes Total:16777216
: q-quickformat, l-lowlevel format, else no format
First with the older one I did, even after low level format about 78kb...
Dito for the new one...
Just to make sure same memory on each board, I update the littlefs to print out data about the identification of the chip...
Which you can see the details from screenshot of three TyCommander windows, where all three chips were programmed at the same time
It is almost like maybe the original chip had something run on it that converted it to work in Quad mode and the newer boards are still running ins single or dual pin SPI? Not sure if that
makes sense?