Forum Rule: Always post complete source code & details to reproduce any issue!
Page 2 of 2 FirstFirst 1 2
Results 26 to 27 of 27

Thread: "Please press the RESET BUTTON on your Teensy to upload your sketch." is all get

  1. #26
    Junior Member
    Join Date
    Jun 2015
    Posts
    1
    Hi Folks,

    OS: Debian 64 bit
    Linux kernel 3.2
    Teensy 3.1

    Got started with my Teensy 3.1 last night and everything went as expected, using just the loader for blink fast/slow and then Teensyduino to get it sending midi messages via USB which I could hapilly see arriving on the laptop.

    Powered off the laptop over night (teensy still connected via USB) & when I next tried to do anything with the loader, nothing happened when I pressed the button (having uploaded a new sketch).

    When I first plugged it in (before having done anything) I noticed it appear in syslog, and listed as USB device (via lsusb). It no longer presents itself in syslog or lsusb when I plug it in.

    I felt sure it must be toasted, but in fiddling about, I notice that if I connect 3.3v to the reset 'pin' on the under side of the board, I get the follwoing in syslog (that I'd expect from just plugging it in to USB):

    Jun 26 16:36:26 grizzly kernel: [ 1023.629189] usb 1-1: new full-speed USB device number 21 using xhci_hcd
    Jun 26 16:36:27 grizzly kernel: [ 1023.650198] usb 1-1: New USB device found, idVendor=16c0, idProduct=0485
    Jun 26 16:36:27 grizzly kernel: [ 1023.650201] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    Jun 26 16:36:27 grizzly kernel: [ 1023.650203] usb 1-1: Product: Teensy MIDI
    Jun 26 16:36:27 grizzly kernel: [ 1023.650204] usb 1-1: Manufacturer: Teensyduino
    Jun 26 16:36:27 grizzly kernel: [ 1023.650205] usb 1-1: SerialNumber: 967050
    Jun 26 16:36:27 grizzly kernel: [ 1023.651499] generic-usb 0003:16C0:0485.0014: hidraw2: USB HID v1.11 Device [Teensyduino Teensy MIDI] on usb-0000:00:14.0-1/input1

    and also...

    lsusb
    Bus 001 Device 019: ID 16c0:0485 VOTI Teensyduino MIDI

    When I then release the 3.3v from the reset pin I get the following in syslog as though I'd disconnected the USB device:

    Jun 26 16:36:56 grizzly kernel: [ 1052.657775] usb 1-1: USB disconnect, device number 21

    Any help I can get would be greatly appreciated.

    Thanks in advance,

    Jim.

  2. #27
    Junior Member
    Join Date
    May 2017
    Posts
    1
    Hey There!!!!

    I've been working with teensy for a while but i decided to upgrade my Windows 10 laptop changing the disk to SSD.

    After installing Arduino and Teensyduino i can't upload the sketch ssutomatically from Arduino...

    The teensy shows on PORT.

    Arduino opens teensy loader but the i does nothing and i need to press reset button.

    Anyone can help????

    Thanks?

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •