Not loading/running program on re-boot. With Teensy 3.1 I can load a sketch with the Arduino IDE, it is programmed into the Teensy and runs. If I disconnect power then re-connect power it re-boots the sketch and runs. If I load the Blinky.bas sketch under BASICtools the Teensy runs the program fine. If I disconnect the USB cable then re-connect the USB cable, or use an external power source the Teensy does not re-boot/doesn't run the program.
Yes, I down loaded BASICtools, yes I purchased, downloaded and copied the Teensy 3.1 personality file into /Program Files (x86)/Coridium/Freescale directory. Everything seems to work fine including Print "Hello World" etc. BUT nothing in ARMbasic appears to remain programmed.
I am running ARMbasic(9.31a) BASICtools(5.28)
If I attempt to load the example BLINKY.hex ARMbasic sketch with the Teensy loader the following is the Verbose info. Note the line where it says it can not find the .elf file. What do I need to change?
09:19:52: File "BLINKY.hex". 19590 bytes, 7% used
09:20:00: Device came online, code_size = 262144
09:20:00: Board is: Teensy 3.1 (MK20DX256), version 1.03
09:20:00: File "BLINKY.hex". 19590 bytes, 7% used
09:20:00: File "BLINKY.hex". 19590 bytes, 7% used
09:20:00: Error: can't open file 'C:\Users\Terry\AppData\Local\Temp\Coridium\BLINKY.elf' (error 2: the system cannot find the file specified.)
09:20:00: Code size from .elf file = 0
09:20:00: begin operation
09:20:00: flash, block=0, bs=1024, auto=1
09:20:00: flash, block=1, bs=1024, auto=1
09:20:00: flash, block=2, bs=1024, auto=1
09:20:00: flash, block=3, bs=1024, auto=1
09:20:00: HID/win32: waiting for device
09:20:00: flash, block=4, bs=1024, auto=1
09:20:01: flash, block=5, bs=1024, auto=1
09:20:01: flash, block=6, bs=1024, auto=1
09:20:01: flash, block=7, bs=1024, auto=1
09:20:01: flash, block=8, bs=1024, auto=1
09:20:01: flash, block=9, bs=1024, auto=1
09:20:01: flash, block=10, bs=1024, auto=1
09:20:01: flash, block=11, bs=1024, auto=1
09:20:01: flash, block=12, bs=1024, auto=1
09:20:01: flash, block=13, bs=1024, auto=1
09:20:01: flash, block=14, bs=1024, auto=1
09:20:01: flash, block=15, bs=1024, auto=1
09:20:01: flash, block=16, bs=1024, auto=1
09:20:01: flash, block=17, bs=1024, auto=1
09:20:01: flash, block=18, bs=1024, auto=1
09:20:01: flash, block=19, bs=1024, auto=1
09:20:01: flash, block=24, bs=1024, auto=1
09:20:01: sending reboot
09:20:01: begin wait_until_offline
09:20:01: offline, waited 2
09:20:01: end operation
09:20:01: redraw timer set, image 14 to show for 1200 ms
09:20:01: HID/win32: vid:045E pid:0745 ver:0656
09:20:01: HID/win32: vid:045E pid:0745 ver:0656
09:20:01: HID/win32: vid:045E pid:0745 ver:0656
09:20:01: HID/win32: vid:045E pid:0745 ver:0656
09:20:01: HID/win32: vid:045E pid:0745 ver:0656
09:20:02: redraw, image 9
09:20:26: Verbose Info event