Error compiling/Multiple libraries for SD.h Issues

[jebojorquez]

Hello all! I am brand new to the forum and so far it has been very resourceful but I have a problem and haven't been able to find any answers in searching the posts. I have recently gotten the Teensy 3.2 and Audio adapter i have breadboarded the tutorial with proper buttons, pots, wires and have the condenser mic and headphones attached etc. My problem now is Im trying to run the first Hardware test of the audio tutorial to no avail. I get an error when i click verify and says error compiling board for teensy 3.2/3.1. As per the forum rules here is the code from the examples:

// Advanced Microcontroller-based Audio Workshop
//
// http://www.pjrc.com/store/audio_tutorial_kit.html
// https://hackaday.io/project/8292-microcontroller-audio-workshop-had-supercon-2015
//
// Part 1-2: Test Hardware
//
// Simple beeping is pre-loaded on the Teensy, so
// it will create sound and print info to the serial
// monitor when plugged into a PC.
//
// This program is supposed to be pre-loaded before
// the workshop, so Teensy+Audio will beep when
// plugged in.

#include <Audio.h>
#include <Wire.h>
#include <SD.h>
#include <SPI.h>
#include <SerialFlash.h>
#include <Bounce.h>

AudioSynthWaveform waveform1;
AudioOutputI2S i2s1;
AudioConnection patchCord1(waveform1, 0, i2s1, 0);
AudioConnection patchCord2(waveform1, 0, i2s1, 1);
AudioControlSGTL5000 sgtl5000_1;

Bounce button0 = Bounce(0, 15);
Bounce button1 = Bounce(1, 15);
Bounce button2 = Bounce(2, 15);

int count=1;
int a1history=0, a2history=0, a3history=0;

void setup() {
AudioMemory(10);
pinMode(0, INPUT_PULLUP);
pinMode(1, INPUT_PULLUP);
pinMode(2, INPUT_PULLUP);
Serial.begin(115200);
sgtl5000_1.enable();
sgtl5000_1.volume(0.3);
waveform1.begin(WAVEFORM_SINE);
delay(1000);
button0.update();
button1.update();
button2.update();
a1history = analogRead(A1);
a2history = analogRead(A2);
a3history = analogRead(A3);
}




void loop() {
Serial.print("Beep #");
Serial.println(count);
count = count + 1;
waveform1.frequency(440);
waveform1.amplitude(0.9);
wait(250);
waveform1.amplitude(0);
wait(1750);
}

void wait(unsigned int milliseconds)
{
elapsedMillis msec=0;

while (msec <= milliseconds) {
button0.update();
button1.update();
button2.update();
if (button0.fallingEdge()) Serial.println("Button (pin 0) Press");
if (button1.fallingEdge()) Serial.println("Button (pin 1) Press");
if (button2.fallingEdge()) Serial.println("Button (pin 2) Press");
if (button0.risingEdge()) Serial.println("Button (pin 0) Release");
if (button1.risingEdge()) Serial.println("Button (pin 1) Release");
if (button2.risingEdge()) Serial.println("Button (pin 2) Release");
int a1 = analogRead(A1);
int a2 = analogRead(A2);
int a3 = analogRead(A3);
if (a1 > a1history + 50 || a1 < a1history - 50) {
Serial.print("Knob (pin A1) = ");
Serial.println(a1);
a1history = a1;
}
if (a2 > a2history + 50 || a2 < a2history - 50) {
Serial.print("Knob (pin A2) = ");
Serial.println(a2);
a2history = a2;
}
if (a3 > a3history + 50 || a3 < a3history - 50) {
Serial.print("Knob (pin A3) = ");
Serial.println(a3);
a3history = a3;
}
}
}

The error message I get after trying to click verify is this:


c:\program files (x86)\arduino\hardware\tools\arm\bin\../lib/gcc/arm-none-eabi/5.4.1/../../../../arm-none-eabi/bin/ar.exe: unable to rename 'C:\Users\Raveen\AppData\Local\Temp\arduino_build_273626\core\core.a'; reason: File exists

Multiple libraries were found for "SD.h"
Used: C:\Program Files (x86)\Arduino\hardware\teensy\avr\libraries\SD
Not used: C:\Program Files (x86)\Arduino\libraries\SD
Error compiling for board Teensy 3.2 / 3.1.

Not really sure what it means I looked around the forum and saw a couple people mention multiple libraries and deleting them but I wasn't sure what was safe to delete. I tried deleting sd.h in the arduino\libraries folder thinking that would help but it did not. Any help would be really appreciated I'm really excited to start but can't figure this first simple step out haha. Thanks for your time!