My host PC is a "fitlet2" Linux Mint MiniPC, and 'uname -a' says
4.15.0-55-generic #60-Ubuntu SMP Tue Jul 2 18:22:20 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux
I am running Arduino 1.8.9 + Teensyduino 1.47 and I have no problem programming a Teensy 4 or a Teensy 3.2 so the setup seems OK.
Also the T4 program input and output via USB serial works OK. However, the T3.2 output window drops many lines, and eventually stops completely, even though I can confirm the Teensy code does continue to run if I add LED blinking. Here's an example showing the problem:
Here is the complete output on the Serial monitor including timestamps, note what's missing:
'dmesg' after a program cycle shows the Teensy disconnects and reconnects as 16C0:0478 (bootloader) and then 16C0:0483 (serial device) after programming, which I think is expected, so I see no obvious clues here:
EDIT: same thing happens trying this code with a Teensy LC, and the Teensy 4 that was working OK before. Something weird about my host PC I guess. I rebooted my Mint box, and now it works "better" in that it reached "Done" at the end, but it still dropped quite a few lines. Including "Done" there are 101 lines, but the Arduino Serial window only displays 77 lines. It is missing line 6, 13, 17, ...etc.
4.15.0-55-generic #60-Ubuntu SMP Tue Jul 2 18:22:20 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux
I am running Arduino 1.8.9 + Teensyduino 1.47 and I have no problem programming a Teensy 4 or a Teensy 3.2 so the setup seems OK.
Also the T4 program input and output via USB serial works OK. However, the T3.2 output window drops many lines, and eventually stops completely, even though I can confirm the Teensy code does continue to run if I add LED blinking. Here's an example showing the problem:
Code:
void setup() {
Serial.begin(115200);
delay(3000);
for (uint8_t i=0; i<100; i++) {
delay(100);
Serial.println(i);
}
Serial.println("Done");
}
void loop() {}
Here is the complete output on the Serial monitor including timestamps, note what's missing:
Code:
15:57:29.334 -> 0
15:57:29.433 -> 1
15:57:29.533 -> 2
15:57:29.633 -> 3
15:57:29.733 -> 4
15:57:30.731 -> 14
15:57:31.530 -> 22
15:57:31.630 -> 23
15:57:31.730 -> 24
15:57:32.329 -> 30
15:57:32.429 -> 31
15:57:32.529 -> 32
15:57:33.028 -> 37
15:57:33.227 -> 39
15:57:33.727 -> 44
15:57:33.826 -> 45
15:57:33.926 -> 46
15:57:34.026 -> 47
15:57:34.126 -> 48
15:57:34.325 -> 50
15:57:34.534 -> 52
15:57:34.634 -> 53
15:57:34.734 -> 54
15:57:34.834 -> 55
15:57:34.933 -> 56
15:57:35.033 -> 57
15:57:36.031 -> 67
15:57:36.331 -> 70
15:57:36.530 -> 72
15:57:36.936 -> 76
'dmesg' after a program cycle shows the Teensy disconnects and reconnects as 16C0:0478 (bootloader) and then 16C0:0483 (serial device) after programming, which I think is expected, so I see no obvious clues here:
Code:
[271857.876069] usb 1-6: USB disconnect, device number 37
[271858.271529] usb 1-6: new full-speed USB device number 38 using xhci_hcd
[271858.420594] usb 1-6: New USB device found, idVendor=16c0, idProduct=0478
[271858.420599] usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[271858.420601] usb 1-6: SerialNumber: 00007834
[271858.421915] hid-generic 0003:16C0:0478.0048: hidraw3: USB HID v1.11 Device [HID 16c0:0478] on usb-0000:00:15.0-6/input0
[271859.007364] usb 1-6: USB disconnect, device number 38
[271859.323516] usb 1-6: new full-speed USB device number 39 using xhci_hcd
[271859.472693] usb 1-6: New USB device found, idVendor=16c0, idProduct=0483
[271859.472697] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[271859.472699] usb 1-6: Product: USB Serial
[271859.472701] usb 1-6: Manufacturer: Teensyduino
[271859.472703] usb 1-6: SerialNumber: 307720
[271859.473306] cdc_acm 1-6:1.0: ttyACM0: USB ACM device
EDIT: same thing happens trying this code with a Teensy LC, and the Teensy 4 that was working OK before. Something weird about my host PC I guess. I rebooted my Mint box, and now it works "better" in that it reached "Done" at the end, but it still dropped quite a few lines. Including "Done" there are 101 lines, but the Arduino Serial window only displays 77 lines. It is missing line 6, 13, 17, ...etc.
Last edited: