hello, new to all this and i have been poking around.
Initially Arduino IDE was not showing teensy boards even after installing Teensyduino.
Deleted everything and started from scratch. everything is peachy.

I have the soldering down, but im new to coding.
Downloaded two codes and tested them separately. they both work exactly how i wanted them to.
i am using two slide switches and one potentiometer. however i have tried to combine them and im not having luck.
i am posting them separately...

#include <ResponsiveAnalogRead.h>

const int pot_pin = A0; // pot input
int potValue; // Stores Pot State
int potMidiValue; // Stores Pot State devided by 8 for MIDI
int conNum; // midi cc control number
int carryVal = 0;

ResponsiveAnalogRead analog(pot_pin, true);

void setup() {
Serial.begin(9600);
}
void loop() {
analog.update(); //update the analouge reading in each pass
potValue = analog.getValue(); // store current state in variable
potMidiValue = potValue / 8; // Makes potVale in to MIDI friendly code

if ((analog.hasChanged()) && (potMidiValue != carryVal)){
usbMIDI.sendControlChange(conNum, potMidiValue, 5);
Serial.println(potMidiValue);
}
carryVal = potMidiValue;
while (usbMIDI.read()) {
}

delay(5);

}
.................................................. ...................
#include <Bounce.h>

const int NUM_OF_BUTTONS = 2;
const int MIDI_CHAN = 5;
const int DEBOUNCE_TIME = 5;

Bounce buttons[NUM_OF_BUTTONS] =
{
Bounce (0, DEBOUNCE_TIME),
Bounce (1, DEBOUNCE_TIME)
};

const int MIDI_MODE_NOTES = 0;
const int MIDI_MODE_CCS = 1;
int midiMode = MIDI_MODE_NOTES;

const int MIDI_NOTE_NUMS[NUM_OF_BUTTONS] = {40, 41};
const int MIDI_NOTE_VELS[NUM_OF_BUTTONS] = {110, 110};
const int MIDI_CC_NUMS[NUM_OF_BUTTONS] = {01, 02};
const int MIDI_CC_VALS[NUM_OF_BUTTONS] = {127, 127};

void setup()
{
for (int i = 0; i < NUM_OF_BUTTONS + 1; i++)
{
pinMode (i, INPUT_PULLUP);
}

}

void loop()
{
for (int i = 0; i < NUM_OF_BUTTONS + 1; i++)
{
buttons[i].update();
}
for (int i = 0; i < NUM_OF_BUTTONS; i++)
{
if (buttons[i + 1].fallingEdge())
{
if (midiMode == MIDI_MODE_NOTES)
usbMIDI.sendNoteOn (MIDI_NOTE_NUMS[i], MIDI_NOTE_VELS[i], MIDI_CHAN);
else
usbMIDI.sendControlChange (MIDI_CC_NUMS[i], MIDI_CC_VALS[i], MIDI_CHAN);
}
else if (buttons[i + 1].risingEdge())
{
if (midiMode == MIDI_MODE_NOTES)
usbMIDI.sendNoteOff (MIDI_NOTE_NUMS[i], 0, MIDI_CHAN);
else
usbMIDI.sendControlChange (MIDI_CC_NUMS[i], 0, MIDI_CHAN);
}

}
if (buttons[0].fallingEdge())
{
midiMode = MIDI_MODE_NOTES;
}
else if (buttons[0].risingEdge())
{
midiMode = MIDI_MODE_CCS;
}
while (usbMIDI.read())
{

}

}


can someone help me combine them properly.

first switch sends signal CH05.CC.01 which is what i wanted. it only outputs one signal. so in the program i am using. i have it mapped to two buttons with an invert on the second so it acts like a toggle between the two. (so wheres CH05.CC.02?)

if i flip the second switch it changes the output of the first switch to NOTEs. however i would like for the second switch to work like the first and send CH05CC.02

the potentiometer works perfect when that code alone is in the teensy.

i want to fix and combine both codes.
at least combine them.. i can work with the second output being notes if anything.
thank you for any help and encouragement.