Can alc883(codec) be wired to teensy?

[FlameOnion]

If so, how?
What is "Sync"?, is WS; FS - Frame Sync?



(datasheet)
alc883.pdf

[FlameOnion]

Is this good?
pin 10(sync) > pin23(teensy 3.2)
pin 6(bitclk)> pin9(teensy 3.2)
pin8(sdata in) > PIN22(teensy 3.2)

what about teensy pin 9 "Output, 11.3 MHz" and alc883 pin6 "24Mhz bit clock input"?

[FlameOnion]

Used this code:

#include <Audio.h>
#include <Wire.h>
#include <SPI.h>
#include <SD.h>
#include <SerialFlash.h>

// GUItool: begin automatically generated code
AudioSynthWaveformSine   sine1;          //xy=204.1999969482422,187.1999969482422
AudioInputUSB            usb1;           //xy=205.1999969482422,93.19999694824219
AudioOutputTDM           tdm1;           //xy=577.1999969482422,134.1999969482422
AudioConnection          patchCord1(sine1, 0, tdm1, 0);
AudioConnection          patchCord2(sine1, 0, tdm1, 1);
AudioConnection          patchCord3(sine1, 0, tdm1, 2);
AudioConnection          patchCord4(sine1, 0, tdm1, 3);
AudioConnection          patchCord5(sine1, 0, tdm1, 4);
AudioConnection          patchCord6(sine1, 0, tdm1, 5);
AudioConnection          patchCord7(sine1, 0, tdm1, 6);
AudioConnection          patchCord8(sine1, 0, tdm1, 7);
AudioConnection          patchCord9(sine1, 0, tdm1, 8);
AudioConnection          patchCord10(sine1, 0, tdm1, 9);
AudioConnection          patchCord11(sine1, 0, tdm1, 10);
AudioConnection          patchCord12(sine1, 0, tdm1, 11);
AudioConnection          patchCord13(sine1, 0, tdm1, 12);
AudioConnection          patchCord14(sine1, 0, tdm1, 13);
AudioConnection          patchCord15(sine1, 0, tdm1, 14);
AudioConnection          patchCord16(sine1, 0, tdm1, 15);
// GUItool: end automatically generated code






void setup() {                
  AudioMemory(60);
  sine1.amplitude(0.9);
  sine1.frequency(720);
}

void loop() {
}

(I used the alc622 schematic, it has same pinout as alc883)

pins I connected to teensy 3.2:
AVDD1 / AVDD2 to 5v
AVSS1 / AVSS2 to agnd

DVDD1 / DVDD2 to 3.3v
DVSS1 / DVSS2 to gnd

JDREF 20k R(not 1%) to gnd
VREF with 10 uf cap to gnd


SYNC to pin23(teensy)
BITCLK to pin9(teensy)
SDATAIN to PIN22(teensy)

cheap headphones to pins(codec) 45,46(Left/Right channels)
2nd cheap headphones to pins(codec) 39,41(Left/Right channels)
line in from PC to pins(codec) 35,36(Left/Right channels)

(the only cap I used was on VREF)


Connected individually 50k pot to pins(codec) 13,34(sense pins) and gnd, changed slowly the pot, I did not hear a single sound from headphones or line in on pc.(tried with prob 5% resistors, and it was the same)
(probed the codec pins without the jacks attached, most of the pins sit at half the dvdd/avdd(~1.6v, ~2.5v)